Diamondback 500 manual Console

Page 15

500tmOM 8/24/06 11:19 AM Page 17

Console (continued)

returns to idle mode.

•Pause a program: You may interrupt or pause a program for up to 30 minutes during a workout before the console resets. To pause a program, simply press “STOP” key once.

o The dot matrix will scroll “PAUSE” during pause mode

o The incline will stay at the current setting; speed will return to 0mph.

o Press “STOP” key one more time during Pause mode, the

program will end and enter workout summary mode.

•Resume a program : To resume a program back to the point of where you left off, either press “START” key during pause mode.

•Switching a program: The user may switch from current operating program to another program during program run mode, cool down or workout summary mode by pressing a program selecting key. Calories and distance will continue accumulating from previous program.

o If “Classic Program” or “HR Interactive” program key is pressed during a program-executing mode, it will enter program-switching mode:

—The dot matrix will switch to display the new program default profile display. You may continue pressing the program selecting key until your desire program LED is lit.

—Press “ENTER” to accept this new program or “START” key to start this new program right away.

—If “ENTER” key is pressed, it will enter this program setup mode; time display will be prompted with default time and wait for an entry. Age and weight default will be the last update.

—Follow the prompts to set up the program. Press “UP/DOWN” key to adjust the setting. When finish, press “START” to start the program, the new program will begin, and Warm Up mode will be skipped.

—If 3 seconds passes after your initial program selecting key pressed and no other key is pressed, the program will resume back to previous activities.

•Re-start a program: The user may re-start a program after the program ends. Simply press “START” key during Cool Down or Workout Summary mode. The program will be started immediately without Warm up. The program default will remain the same as previous program; the calories and distance will continue accumulating.

•Speed adjustment: When speed adjustment is allowed by a program, you may adjust the speed from 0 mph to 11 mph by pressing SPEED UP/DOWN key.

o Dot matrix profile will adjust the display according to the Speed

500 Tm Owner’s Manual

15

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 500tmOM 8/24/06 1118 AM To Activate Warranty Purchaser’s Reference InformationShipping Materials Table of Contents Introduction Safety Instructions and Warnings Grounding Instructions Safety Instructions & WarningsAssembly Instructions Upright Posts AssemblyConsole Assembly Handrail Cover Assembly Handrail AssemblyFinish Up Motor Cover Assembly’10 BMI = weight lb ÷ height2 in xWorkout guidelines Good health is an exercise in common sense157 85% of Maximum Quantity & QualityGet a smart start on exercising Built in Wireless Heart Rate Receiver Heart Rate Monitoring DevicesErratic Heart Rate Readings Console Console Console Profile display Console LayoutDisplays Dot Matrix /Profile display Workout data display Speed and Incline displayOther data displays Enter key Safety keyFunction keys Speed Up/Down keys Incline Up/Down keysDuring the Program Workout ProgramsGetting Started Beginning the ProgramO L D O W N I C K S T a R T Start KeyClassic Programs Program Default ValuesWorkout Programs Interval Trainer Segment Speed Incline Hill Walk Random Hills Easy JOG Segment Speed Incline 5K Train I N T E R a C T I V E P R O G R a M S Target HR HR Intervals Workout Programs Workout Programs Effective August Domestic warranty InformationTo obtain service Warranty RegistrationAdditional Rights Warranty voided ifParts & Service ExclusionsBelt Adjustment MaintenanceOverall Cleaning Belt/Deck MaintenanceTurn each time on both sides 500tmOM 8/24/06 1119 AM 500tmOM 8/24/06 1119 AM Diamondback Fitness Warranty Card Warranty cardDiamondback Fitness
Top Page Image Contents