Gold's Gym GGTL80608.0 manual Not to pinch the wires

Page 10

10. Insert the wires from the console assembly into	10
the handrail assembly.	10
Attach the console assembly to the handrail as-		Console
sembly with four 1/4" x 3/4" Bolts (5). Be careful		Console
not to pinch the wires.		Assembly
		Handrail
		Assembly
			5	Wires	5
			5
11. Identify the Storage Latch (53). Remove the tie	11
from the end of the tube. Make sure that the	11
sleeve has been slid over the indicated hole and
that the Latch Knob (54) is locked into the hole.		54
Pull on the sleeve to make sure that it is		54
locked into place.		Tube		Hole
		Tube		Hole
		Sleeve		53
				53
12. Raise the Frame (56) to the position shown.	12	56
Have a second person hold the Frame until	12	56
this step is completed.
Orient the Storage Latch (53) so that the large		8	4
barrel and the Latch Knob (54) are in the posi-		8	4
tions shown. Attach the Latch Bracket (14) and			53
Storage Latch (53) to the Base (83) with two 3/8"		54	53
x 2" Bolts (4) and two 3/8" Nuts (8).		54	Large
Attach the upper end of the Storage Latch (53)			Barrel
to the bracket on the Frame (56) with a 3/8" x 2"
Bolt (4) and a 3/8" Nut (8). Note: It may be nec-			14	83
essary to move the Frame back and forth to			14	83
align the Storage Latch with the bracket.
Lower the Frame (56) (see HOW TO LOWER		8		4
THE TREADMILL FOR USE on page 24).		8		4

13.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see pages 26 and 27).

10

Image 10

Contents QUESTIONS? Model No. GGTL80608.0 Serial NoTable of Contents Pulse sensor is not a medical device Important PrecautionsVarious factors, including the users move Page Before YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedNot to pinch the Upright Wire Nut the Wheel must turn freely. DiscardBe careful not to pinch the Upright Wire Fully tighten the Bolts yetNot Connected PROPERLY, the CON Sole MAY be Damaged When Power is Turned onSole MAY be Damaged When Power is Turned on Not Connected PROPERLY, the CONNot to pinch the wires Pull on the sleeve to make sure that it is Locked into placeBe careful not to pinch the wires. Reattach HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeRun Measure your heart rate if desired Select a preset workout HOW to USE a Preset WorkoutPress the Start button to start the workout Select the Custom Workout Center HOW to USE the Custom Workout CenterPress the Start Workout button to start the workout Select the fitness test workout HOW to USE the Fitness Test WorkoutPut on the chest pulse sensor Press the Start Fitness Test button to start the workoutHOW to USE the Sound System Connector is fully pluggedHOW to USE AN Ifit Card Insert an iFit card and select a workoutInformation Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part LIST-Model No. GGTL80608.0 Key No. Qty Description105 #8 x 2 Screw Userʼs Manual 106 Right Handrail Trim Exploded Drawing A-Model No. GGTL80608.0 R1108A Exploded Drawing B-Model No. GGTL80608.0 R1108A Exploded Drawing C-Model No. GGTL80608.0 R1108A Exploded Drawing D-Model No. GGTL80608.0 R1108A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT