Gold's Gym GGTL80608.0 manual Not Connected PROPERLY, the CON Sole MAY be Damaged When

Page 9

7. Attach the Tray (90) to the handrail assembly	7			1	90
with two #8 x 1/2" Screws (1).				1	90		Handrail
Have a second person hold the handrail assem-						1	Handrail
bly near the Right Upright (78) and the Left						1	Assembly
Upright (74). Connect the Upright Wire (38) to
the console wire. See the inset drawing. The
connectors should slide together easily and
snap into place. If they do not, turn one connec-				74
tor and try again. IF THE CONNECTORS ARE				74
NOT CONNECTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE		Console
POWER IS TURNED ON.		Console						38
Remove the wire tie from the Upright Wire (38).		Wire			Console			38
Remove the wire tie from the Upright Wire (38).			38

						Wire
					Wire Tie		78
							78
8. Set the handrail assembly on the Uprights (74,	8						Handrail
78). Be careful not to pinch the wires.	8						Handrail
Attach the handrail assembly to the Uprights							Assembly
(74, 78) with six 5/16" x 1" Bolts (7) and six
5/16" Star Washers (10) as shown.
See assembly steps 4 and 6. Firmly tighten	7	10	10	7	7
the 3/8" x 4" Bolts (6).	7	10	10	7	7
			74		10
			74			7	78	10
						7	78
9. With the help of a second person, hold the con-	9
sole assembly near the handrail assembly.	9		Console
Connect the two wires from the console assem-			Console
bly to the two wires from the handrail assembly.			Assembly
See the inset drawing in step 7. The connec-
tors should slide together easily and snap
into place. If they do not, turn one connector				Wires
and try again. IF THE CONNECTORS ARE				Wires
NOT CONNECTED PROPERLY, THE CON-							Wires
SOLE MAY BE DAMAGED WHEN THE							Wires
POWER IS TURNED ON.

Handrail

Assembly

9

Image 9

Contents Model No. GGTL80608.0 Serial No QUESTIONS?Table of Contents Important Precautions Pulse sensor is not a medical deviceVarious factors, including the users move Page Before YOU Begin Assembly Not to pinch the Upright Wire Make sure that the power cord is unpluggedDo not fully fold the Frame yet Nut the Wheel must turn freely. DiscardFully tighten the Bolts yet Be careful not to pinch the Upright WireSole MAY be Damaged When Power is Turned on Power is Turned onNot Connected PROPERLY, the CON Sole MAY be Damaged When Not Connected PROPERLY, the CONPull on the sleeve to make sure that it is Locked into place Not to pinch the wiresBe careful not to pinch the wires. Reattach Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerRun Measure your heart rate if desired HOW to USE a Preset Workout Select a preset workoutPress the Start button to start the workout HOW to USE the Custom Workout Center Select the Custom Workout CenterPress the Start Workout button to start the workout Put on the chest pulse sensor HOW to USE the Fitness Test WorkoutSelect the fitness test workout Press the Start Fitness Test button to start the workoutConnector is fully plugged HOW to USE the Sound SystemInsert an iFit card and select a workout HOW to USE AN Ifit CardOptional Chest Pulse Sensor Information ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description Part LIST-Model No. GGTL80608.0105 #8 x 2 Screw Userʼs Manual 106 Right Handrail Trim Exploded Drawing A-Model No. GGTL80608.0 R1108A Exploded Drawing B-Model No. GGTL80608.0 R1108A Exploded Drawing C-Model No. GGTL80608.0 R1108A Exploded Drawing D-Model No. GGTL80608.0 R1108A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT