Gold's Gym GGTL80608.0 manual Top, Problem The walking belt slows when walked on

Page 26
2–3 in.
Rear Roller Bolts

Remove the three #8 x 3/4" Screws (12) and care-

 

 

fully pivot the Hood (61) off.

61

12

 

 

 

Locate the Reed Switch (71) and the Magnet (50)

 

 

on the left side of the Pulley (51). Turn the Pulley

 

 

until the Magnet is aligned with the Reed Switch.

 

 

Make sure that the gap between the Magnet and

1/8 in.

 

the Reed Switch is about 1/8 in. (3 mm). If neces-

 

sary, loosen the 3/4" Reed Switch Screw (15),

71

50

move the Reed Switch slightly, and then retighten

the Screw. Reattach the Hood (not shown), and run

 

51

the treadmill for a few minutes to check for a cor-

Top

 

rect speed reading.

 

 

View

 

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor- b mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG

THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

c. If the walking belt still slows when walked on, see the front cover of this manual.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents QUESTIONS? Model No. GGTL80608.0 Serial NoTable of Contents Various factors, including the users move Important PrecautionsPulse sensor is not a medical device Page Before YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedNot to pinch the Upright Wire Nut the Wheel must turn freely. DiscardBe careful not to pinch the Upright Wire Fully tighten the Bolts yetNot Connected PROPERLY, the CON Sole MAY be Damaged When Power is Turned onSole MAY be Damaged When Power is Turned on Not Connected PROPERLY, the CONNot to pinch the wires Pull on the sleeve to make sure that it is Locked into placeBe careful not to pinch the wires. Reattach PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeRun Measure your heart rate if desired Press the Start button to start the workout HOW to USE a Preset WorkoutSelect a preset workout Press the Start Workout button to start the workout HOW to USE the Custom Workout CenterSelect the Custom Workout Center Select the fitness test workout HOW to USE the Fitness Test WorkoutPut on the chest pulse sensor Press the Start Fitness Test button to start the workoutHOW to USE the Sound System Connector is fully pluggedHOW to USE AN Ifit Card Insert an iFit card and select a workoutInformation Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part LIST-Model No. GGTL80608.0 Key No. Qty Description105 #8 x 2 Screw Userʼs Manual 106 Right Handrail Trim Exploded Drawing A-Model No. GGTL80608.0 R1108A Exploded Drawing B-Model No. GGTL80608.0 R1108A Exploded Drawing C-Model No. GGTL80608.0 R1108A Exploded Drawing D-Model No. GGTL80608.0 R1108A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents