JVC RX-9000VBK manual Basic Settings, Setting the Front Speakers Either for Main Room or Sub-room

Page 25
SOURCE SELECTOR

Basic Settings

Some of the following settings are required after connecting and positioning your speakers, while others will make operations easier.

The following operations are only possible while the receiver is ready for the main room operations.

IMPORTANT:

When using the buttons and controls on the front panel:

Check the following lamps’ illumination.

For the main room operations:

The MAIN ROOM ON/OFF lamp is lit.

The SUB ROOM CONTROL lamp is not lit.

When using the remote control:

Check to see if the multi-room operation selector and the remote control mode selector are set to the correct positions:

Multi-room operation selector:

Setting the Front Speakers Either for the

Main Room or Sub-room

You can use the front speakers connected to the FRONT 2/SUB ROOM SPEAKERS terminals either as the 2nd front speakers in the main room or as the front speakers in the sub-room.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

To operate this receiver for the main room, set

it to “MAIN ROOM.”

Remote control mode selector:

MAIN

 

 

 

 

 

SUB

ROOM

 

 

 

ROOM

To operate this receiver, set it to “AUDIO/TV/

 

 

 

 

 

 

 

VCR.”

AUDIO/

 

 

 

 

 

TV/VCR

 

 

 

 

 

 

 

 

 

 

 

 

 

On the front panel ONLY:

1. Press SETTING repeatedly until “SPEAKER 2” appears on the display.

SETTING

CATV/DBS

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display when you select the MD recorder or DBS tuner as the source.

On the front panel ONLY:

1. When changing the source name from “TAPE” to “MD”:

Turn SOURCE SELECTOR until “TAPE” appears.

When changing the source name from “TV SOUND” to “DBS”:

Turn SOURCE SELECTOR until “TV SOUND” appears.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to specify the way you want to use the speakers connected to the FRONT 2/SUB ROOM terminals.

• As you turn it, the display changes to show the following:

MAIN SUB

MAIN: Select this to use as the 2nd front speakers in the main room.

SUB: Select this to use as the front speakers in the sub- room.

Setting the Subwoofer Information

Register whether or not you have connected a subwoofer.

Before you start, remember....

2. Press and hold SOURCE NAME (BASS BOOST) until “ASSGN.

BASS BOOST

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel:

SOURCENAME

MD” or “ASSGN. DBS” appears on the display.

To change the source name to “TAPE” or “TV SOUND,” repeat

the same procedure above — in step 1, select “MD” or “DBS” then press and hold SOURCE NAME (BASS BOOST).

Notes:

You can only assign the correct source name to “TAPE/MD” and “TV SOUND/DBS,” but not to “CDR/VCR 2.”

Without changing the source name, you can still use the connected components. However, there may be some inconvenience.

“TAPE” or “TV SOUND” will appear on the display when you select the MD recorder or DBS tuner.

You cannot use the digital input (see page 26) for the MD recorder.

You cannot use the COMPU LINK remote control system (see page 47) to operate the MD recorder.

SETTING

1.Press SETTING repeatedly until “SUBWOOFER” appears on the

display.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to register whether you have connected a subwoofer or not.

As you turn it, the subwoofer setting alternates between “YES” and “NO.”

YES: Select this when a subwoofer is used. SUBWFR lights up on the display (see page 16).

NO: Select this when no subwoofer is used.

23

Image 25
Contents RX-9000VBK For the main unit Table of Contents Precautions FeaturesIntroduction Parts Identification Remote Control Front PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers AM Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker Analog connectionsCD recorder Cassette deck or MD recorderVideo component connections TV and/or DBS tuner Video cameraDVD player Digital input terminals Digital connectionsDBS tuner DVD player Digital output terminalTo set up the RF rod antenna Find the place where you attach the IR signal transmitterTo set up the IR signal transmitter Insert the RF rod antenna to the RF Remote Antenna terminalConnecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Replace the coverRequired Speaker Connections for the Sub-room Multi-room OperationsConnection  Connection ı MeritsPress Power Basic Operating Procedure for Main RoomPress Audio Power on Select and play a sourceGreen Basic Operating Procedure for Sub-RoomSub-room Set the multi-room operation selector to SUB RoomCanceling the Main Room Operations Turning the Power On and Off StandbyMain Room Basic Operations When digital input is selected Lights up when the left Signal and speaker indicators on the displayWhen analog input is selected Always lights up Selecting the Main Room Source to PlayActivating the Main Room Front Speakers Adjusting the Main Room VolumeEtc Selecting different sources for picture and soundAdjusting the Subwoofer Output Level Attenuating the Input SignalMuting the Main Room Sound Reinforcing the BassUsing the Sleep Timer Adjusting the Front Speaker Output BalanceChanging the Display Brightness Recording a SourcePress SUB Room Control Sub-Room OperationsPress SUB Room ON/OFF For the sub-room operationsSelecting the Sub-room Source to Play Canceling the Sub-room OperationsTo use this receiver for the sub-room operations again Selected source name for sub-room appearsOperating the Playback Source for Sub-room Adjusting the Sub-room Volume Muting the Sub-room SoundActivating the Sub-room Front Speakers Press Muting to mute the sound throughSetting the Front Speakers Either for Main Room or Sub-room Basic SettingsSetting the Subwoofer Information Changing the Source NamePress Setting repeatedly until Setting the Speakers for the DSP ModesRear Delay appears on Display Turn Multi JOG to select Delay time of the rear speakerOutput Frequency appears on the displaySettings Digital Input Digital in Terminal SettingSelecting the Analog or Digital Input Mode OPT. DIG. in appears on DisplayShowing the Text Information on Display Adjust the sound using the functions listed above Storing the Basic Settings Adjustments One Touch OperationPress ONE Touch OPERATION. Onetouchoperation MemoTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Press TUNER/SEA MemorySelecting the FM Reception Mode Assigning Names to Preset StationsSelecting Your Favorite SEA Mode Using the SEA ModesCreating Your Own SEA Mode What are the DSP Modes? Using the DSP ModesSurround modes Reproducing the Sound Field DVD Multi Playback ModeDAP modes 3D-PHONIC modesAvailable DSP Modes According to the Speaker Arrangement By pressing DSP Mode By pressing Surround ModeSpeaker arrangements Available DSP modes To activate the SurroundAdjusting the Surround Modes Adjust the center tone Adjust the rear toneTheater appears on Display Adjust the speaker output levels Large Theater or DIG LAdjust the liveness Adjust the room size senseAdjust the overall level of the effects Press Surround ModePress DSP Mode repeatedly until Adjusting the DAP ModesDAP mode Live Club HALL, or Concert Arena Appears on the displayConcert HALL, or Concert Arena appears on the display Repeatedly until the DAP modeActivating the DSP Modes Mode you want appears on DisplaySelect and play a sound source Activating the DVD Multi Playback Mode Using the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the displayWhen you finish, press Exit Using the On-Screen MenusPress Menu Press %/ Þto move to VisualPress %/ Þto move Press %/ Þto move to Sound CONTROL, then press @/ #Press %/ Þto move To Surround LEVEL, then press @/ # Adjusting the DVD Multi Playback ModeFor Dolby Pro Logic For Dolby Digital and DTS Digital SurroundPress SET to store the setting into the SEA Press %/ Þ/ @/ #to adjust the SEA mode as you wantPress %/ Þto move To SETTING, then press @/ # Press %/ Þto move to SEA, then press @ / #Press %/ Þto move To Preset MEMORY, then press @/ # Press %/ Þto move To Preset Name Then press SETPreset station number Press %/ Þto move to Tuner CONTROL, then press @/ #Remote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemCD player CD recorder Cassette deck MD recorder Automatic Source SelectionSynchronized Recording Same timeCD player MD recorder Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerDisc Information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen To exit from the Disc information screenPress %/ Þto move To SEARCH, then Press SET Press Text Display while CD is selected as the sourcePress %/ Þto move To Performer Then press SET Press SET againPress %/ Þto move To GENRE, then Press SET Press %/ Þto move to Search Then press SETPress %/ Þto move To Title INPUT, then press SET Entering the Disc InformationPress Text Display while MD is selected as the source Press %/ Þto move to the genre you want, then press SETPress %/ Þto move to Title Input Then press SET For the MD recorderTarget video components AV Compu Link Remote Control SystemIf the AV Compu Link terminal on the TV is RECEIVER/AMP If the AV Compu Link terminal on the TV is AV Compu Link EXTerminals Video terminals CASE1 If the components are equipped with the S-videoOne-Touch Video Play Automatic Power On Automatic Power On/Off StandbyOne-Touch DVD Play Tuner Operating JVC’s Audio/Video ComponentsSound control section Amplifier CD playerCD recorder CD player-changerTurntable Cassette deckDVD player VCR 1 VCR connected to VCR 1 jacksMulti only for the main room Operations, these buttons can beSet the remote control mode to CATV/DBS Release TV/CATV/DBS PowerIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentRelease VCR 1 Power Try to operate your VCR by pressing VCR 1 PowerIf there are more than one code listed for your brand 11, 44 28, 29, 60Echostar Expressvu General Instrument Hitachi Panasonic PrimestarProblem Possible Cause Solution TroubleshootingConnect an Ntsc TV Amplifier SpecificationsFM tuner IHF AM tunerValley Road Wayne, NJ 781 954 6501099 Limited Warranty AUDIO-2 0200HIMMDWJEIN

RX-9000VBK specifications

The JVC RX-9000VBK is a powerful and versatile A/V receiver designed to cater to the needs of audiophiles and home theater enthusiasts alike. With a sleek, modern design, this receiver combines advanced technology with user-friendly features to deliver an exceptional audio and visual experience.

One of the standout features of the RX-9000VBK is its impressive power output. With a total of 100 watts per channel, this receiver can drive even large speakers with ease, ensuring that you enjoy your favorite movies, music, and games with robust sound. The built-in 7.1 channel surround sound capability creates an immersive audio experience, making you feel like you are part of the action.

The RX-9000VBK is equipped with JVC's proprietary HD Codec, which enhances the audio quality by providing high-definition sound processing. This technology ensures that audio tracks are reproduced accurately, capturing the nuances of every detail. The receiver also supports a variety of audio formats, including Dolby Digital and DTS, allowing you to enjoy your media in the best possible quality.

In addition to its impressive audio capabilities, the JVC RX-9000VBK offers a range of connectivity options. It features multiple HDMI inputs, enabling you to connect various devices such as Blu-ray players, gaming consoles, and streaming devices. The integrated HDMI ARC (Audio Return Channel) allows for easy connection to your TV, simplifying the overall setup.

The user interface of the RX-9000VBK is designed with convenience in mind. It includes an intuitive on-screen display that makes navigation simple, whether you’re adjusting audio settings or selecting input sources. The receiver also comes with a remote control, providing you with the flexibility to operate your home theater system from anywhere in the room.

Additionally, the JVC RX-9000VBK includes a built-in FM tuner, allowing you to enjoy your favorite radio stations with crystal-clear sound quality. The receiver is also compatible with external audio sources, including USB drives and musical instruments, making it a great choice for musicians and music lovers.

Overall, the JVC RX-9000VBK stands out for its robust power, advanced audio technologies, and thoughtful design. It is an excellent choice for anyone looking to enhance their home audio experience, providing both performance and versatility in a single package. Whether you are hosting movie nights, gaming sessions, or simply enjoying your favorite playlists, the RX-9000VBK is sure to deliver exceptional sound quality and performance.