JVC RX-9000VBK manual Adjust the rear tone, Adjust the center tone, Large Theater or DIG L

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Press SURROUND ON/OFF to	SURROUND ON/OFF
activate an appropriate Surround
mode — PRO LOGIC, DOLBY
DIGITAL or DTS SURROUND.

•Each time you press the button, the Surround mode turns on and off alternately.

•When “PRO LOGIC” is selected, the Ù PRO LOGIC indicator lights up on the display.

2. Adjust the speaker output levels.	BALANCE/SURROUND
		ADJUST

1)Press BALANCE/SURROUND ADJUST repeatedly until one of the indications appears on the display. “CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

2) Turn MULTI JOG to adjust the	MULTI JOG
selected speaker output level (from –10
dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

4. Adjust the rear tone.	BALANCE/SURROUND
1) Press BALANCE/SURROUND		ADJUST
ADJUST repeatedly until “REAR
TONE” appears on the display.
The display changes to show the current
setting.		MULTI JOG
2) Turn MULTI JOG to select the rear
tone level you want.
• As you turn it, the display changes to
show the following:

REAR SHARP1 REAR SHARP2 REAR FLAT

(Canceled)

REAR SOFT 1 REAR SOFT 2

To make the rear sounds clearer, select “REAR SHARP1” (a

little) or “REAR SHARP2” (much).

To make the rear sounds softer, select “REAR SOFT 1” (a little) or “REAR SOFT 2” (much).

When “REAR FLAT” is selected, no adjustment is applied.

JVC Theater Surround adjustments

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 24).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

• You cannot adjust the rear speaker output levels and rear tone

when you have set “REAR SPK” to “NONE.” See page 24.

3.Adjust the center tone.

1)Press BALANCE/SURROUND ADJUST repeatedly until “CENTER TONE” appears on the display.

The display changes to show the current setting.

2)Turn MULTI JOG to select the center tone level you want.

BALANCE/SURROUND

ADJUST

MULTI JOG

• You cannot adjust the center speaker output level and center tone

when you have set “CENTER SPK” to “NONE.” See page 24.

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

•As you turn it, the display changes to show the following:

CENTER SHARP1 CENTER SHARP2 CENTER FLAT

(Canceled)

CENTER SOFT 1 CENTER SOFT 2

To make the dialogue clearer, select “CENTER SHARP1” (a

little) or “CENTER SHARP2” (much).

To make the dialogue softer, select “CENTER SOFT 1” (a

little) or “CENTER SOFT 2” (much).

When “CENTER FLAT” is selected, no adjustment is applied.

1. Press DSP MODE repeatedly until		DSP MODE
“LARGE THEATER (or DIG L.
THEATER, DTS L. THEATER)”
or “SMALL THEATER (or DIG
S. THEATER, DTS S.
THEATER)” appears on the
display.
2. Adjust the speaker output levels.	BALANCE/SURROUND
1) Press BALANCE/SURROUND
		ADJUST
ADJUST repeatedly until one of the
indications appears on the display.

“CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

MULTI JOG

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

2)Turn MULTI JOG to adjust the selected speaker output level (from –10 dB to +10 dB).

36