JVC RX-9000VBK manual Receiving Radio Broadcasts, Using Preset Tuning, Tuning in Stations Manually

Receiving Radio Broadcasts

You can browse through all the stations or use the preset function to go immediately to a particular station.

Indicates the functions YOU CAN ALSO USE when the receiver is ready for the sub-room operations.

IMPORTANT:

When using the buttons and controls on the front panel:

Check the following lamps’ illumination.

For the main room operations:

•The MAIN ROOM ON/OFF lamp is lit.

•The SUB ROOM CONTROL lamp is not lit.

Notes:

•When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display. When an FM stereo program is received, the STEREO indicator also lights up.

•You can only select the same station of the same band (FM or AM) both for the main room and sub-room operations. If you change the station for the sub-room, it also changes for the main room (and vice versa). This also means that if you change the station for the sub-room while recording a broadcasting program in the main room, recording in the main room will be interrupted.

For the sub-room operations:

•The SUB ROOM ON/OFF lamp is lit.

•The SUB ROOM CONTROL lamp is lit.

When using the remote control:

Check to see if the multi-room operation selector and the remote control mode selector are set to the correct positions:

Using Preset Tuning

Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 30 FM and 15 AM stations.

To store the preset stations

Multi-room operation selector:

To operate this receiver for the main room, set

it to “MAIN ROOM.”

To operate this receiver for the sub-room, set it

to “SUB ROOM.”

Remote control mode selector:

To operate this receiver, set it to “AUDIO/TV/

VCR.”

MAIN SUB

ROOM ROOM

AUDIO/

TV/VCR

CATV/DBS

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1.Tune in the station you want to preset (see “Tuning in Stations Manually”).

•If you want to store the FM reception mode for this station, select the FM reception mode you want. See “Selecting the FM Reception Mode” on page 30.

Tuning in Stations Manually

On the front panel:

1. Turn SOURCE SELECTOR to select the band (FM or AM).

SOURCE SELECTOR

2. Press TUNER/SEA MEMORY.

TUNER/SEA MEMORY

The last received station of the selected band is tuned in.

2.Press FM/AM TUNING.

3.Turn MULTI JOG until you find the frequency you want.

•Turning it clockwise increases the frequency.

•Turning it counterclockwise decreases the frequency.

•When you turn MULTI JOG quickly, the frequency keeps changing until a station is tuned in.

FM/AM TUNING

MULTI JOG

“CH-” appears and the channel number position starts flashing on the display for about 10 seconds.

MULTI JOG

3.Turn MULTI JOG to select a channel number while the channel number position is flashing.

Note:

You can use the 10 keys on the remote control to select the preset number. When using the 10 keys, be sure that they are activated for the tuner, not for the CD and others. (See page 57.)

4. Press TUNER/SEA MEMORY	TUNER/SEA MEMORY
again while the selected channel
number is flashing on the display.

The selected channel number stops flashing.

The station is assigned to the selected channel number.

From the remote control:

1.Press FM/AM to select the band.

•Each time you press the button, the band alternates between FM and AM.

2.Press TUNING UP or TUNING DOWN repeatedly until you find the frequency you want.

FM/AM

FF/

TUNING UP

/REW

5.Repeat steps 1 to 4 until you store all the stations you want.

To erase a stored preset station

Storing a new station on a used number erases the previously stored one.

• When you hold the button (and release it), the frequency keeps changing until a station is tuned in.

DOWN TUNING

29