JVC RX-9000VBK manual Using the DVD Multi Playback Mode, Activating the DVD Multi Playback Mode

Using the DVD MULTI Playback Mode

This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD player. Before playing back a DVD, refer also to the manual supplied with the DVD player.

The following operations are only possible while the receiver is ready for the main room operations, and are only used for the main room source — DVD MULTI.

IMPORTANT:	If you need to make any adjustment, go to the following
When using the buttons and controls on the front panel:	steps.

Check the following lamps’ illumination.

For the main room operations:

•The MAIN ROOM ON/OFF lamp is lit.

•The SUB ROOM CONTROL lamp is not lit.

When using the remote control:

Check to see if the multi-room operation selector and the remote control mode selector are set to the correct positions:

• Multi-room operation selector:

To operate this receiver for the main room,

set it to “MAIN ROOM.”	MAIN		SUB
	ROOM	ROOM

3.Adjust the speaker output levels.

1)Press BALANCE/SURROUND ADJUST repeatedly until one of the indications appears on the display. “CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

BALANCE/SURROUND

ADJUST

MULTI JOG

• Remote control mode selector:
To operate this receiver, set it to “AUDIO/TV/	AUDIO/
VCR.”	TV/VCR
	CATV/DBS

Activating the DVD MULTI Playback Mode

You can adjust the DVD MULTI playback mode while playing back a DVD using the analog discrete output mode on the DVD player. Once you have made adjustments, the receiver memorizes the adjustments until you change them. You also need to set the DVD player to the analog discrete output mode.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

2)Turn MULTI JOG to adjust the selected speaker output level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

From the remote control:

1. Press DVD MULTI so that “DVD	DVD MUILTI
MULTI” appears on the display.

Notes:

•When you select “DVD MULTI” as the main room source to play, the DSP mode is canceled temporarily, and the SURROUND ON/OFF and DSP MODE buttons do not work.

•When the SUB ROOM ON/OFF lamp and the SUB ROOM speaker (SPEAKERS 2) lamp on the front panel are lit green, you cannot select “DVD MULTI” as the main room source.

On the front panel:

1. Turn SOURCE SELECTOR until	SOURCE SELECTOR
“DVD MULTI” appears on the
display.

2.Select the analog discrete output mode on the DVD player, and start playing a DVD.

• Refer to the manual supplied with the DVD player.

If you need to make any adjustment, go to the following

Notes:

• When you select “DVD MULTI” as the main room source to play,

steps.

3. Press SOUND.

SOUND

the DSP mode is canceled temporarily, and the SURROUND

ON/OFF and DSP MODE buttons do not work.

• When the SUB ROOM ON/OFF lamp and the SUB ROOM

speaker (SPEAKERS 2) lamp on the front panel are lit green,

you cannot select “DVD MULTI” as the main room source.

2. Select the analog discrete output mode on the

DVD player, and start playing a DVD.

• Refer to the manual supplied with the DVD player.

The 10 keys are activated for adjusting the sound.

4.Adjust the speaker output levels.

•To adjust the center speaker level, press CENTER –/+ (from – 10 dB to +10 dB).

•To adjust the left rear speaker level, press REAR•L –/+ (from –10 dB to +10 dB).

•To adjust the right rear speaker level, press REAR•R –/+ (from –10 dB to +10 dB).

CENTER REAR•L REAR•R

2 3 5 6 8 9

MENU ENTER

41