Precor 9.21i owner manual Setting Up the Low Impact Treadmill, Installation Requirements

Page 9

2

CAUTION: Do not remove or otherwise bypass the 3-prong plug with an adapter or extension cord in order to use a non-grounded outlet. Electrical damage can occur if the treadmill is connected to an improper power source.

Setting Up the Low Impact Treadmill

You do not need any special knowledge or experience to set up a M9.21i or M9.21si treadmill. However, you must review and follow the instructions in this manual. If you do not assemble and use the treadmill according to the following guidelines, you might void the Precor limited warranty.

Installation Requirements

Follow these installation requirements when installing the treadmill:

Acquire the appropriate tools. In addition to the tools supplied in the hardware kit, you will need a phillips head screwdriver to remove the hood from the treadmill.

Fill out and mail the limited warranty card. The serial number is printed on a label located underneath the treadmill on the left, rear corner of the running bed. Write the serial number onto the limited warranty card and in this manual before assembling the treadmill. Refer to Obtaining Service.

Set up the M9.21i or M9.21si treadmill on a solid, flat surface. Do not install the treadmill on deeply padded, plush, or shag carpeting due to possible damage to the carpet and machine. If the treadmill is installed in a carpeted area, place a piece of heavy cardboard, plywood, or other solid, smooth, flat surface under the unit. If the floor is not even, the running belt will not track properly. Refer to Checking the Alignment of the Running Belt.

Locate the treadmill at least 4 feet from walls and furniture. Be sure to provide ample space in front of the machine to allow easy access to the ON/OFF switch. Open space to the sides and back of the machine makes for a safer mount and dismount and easier belt adjustment.

Use a standard 120-volt household outlet. The M9.21i or M9.21si treadmill is for household use only. Precor recommends plugging the treadmill into an outlet that is connected to a dedicated 20 amp house circuit breaker. A 20 amp circuit breaker inside the treadmill also helps protects the electrical and electronic components from sustained overloads. An integral 3-prong, grounded plug meets safety requirements and protects the machine.

Assembly Instructions

To assist you in the assembly of the treadmill, the items in the hardware kit shown in Diagram 1, correspond to a particular letter in the alphabet. These letters appear throughout the assembly instructions. If necessary, refer to Diagram 1 while performing the steps below.

To assemble the M9.21i or M9.21si treadmill, take the following steps:

1.Locate the power switch at the front of the treadmill. Make sure that the power switch is in the OFF (O) position and unplug the treadmill’s power cord from the power outlet. Do not assemble the M9.21i or M9.21si treadmill if it is plugged into a power source.

page 9

Image 9
Contents USA Important Safety Instructions Precor Heart Rate Option-Safety Guidelines Personal SafetyFederal Communications Commission, Part Information Regarding Use in the U.S.A. and CanadaGrounding Instructions Canadian Department of CommunicationsSetting Up the Low Impact Treadmill Table of ContentsUsing the Precor Heart Rate Option Working Out on the Low Impact TreadmillUnpacking the M9.21i or M9.21si Low Impact Treadmill Before You BeginHardware Kit DiagramSetting Up the Low Impact Treadmill Installation RequirementsAssembly Instructions Lower board HoodSecure Diagram Bottle cage If the running belt,… Then Checking the Alignment of the Running BeltUsing the Low Impact Treadmill Locating the on and OFF SwitchUsing the Magnetic Safety Key Displays on the Electronic Console Understanding the Electronic ConsoleKeys on the Electronic Console If you want Then Customizing the DisplayWorking Out on the Low Impact Treadmill Start working out End workoutReview workout statistics Pausing Your Workout Using the Quick Start FeatureRetrieving the Previous Workout Program Cooling Down After a WorkoutChanging the Interval Course Profile Using the Weight Loss Program Medium HighHigh Using the Manual Course Program Using the Random CourseUsing a Preprogrammed Course on the M9.21si Deleting Custom Courses on the M9.21si Creating Custom Courses on the M9.21siWearing the Chest Strap Transmitter Using the Precor Heart Rate OptionUtilizing the Heart Rate Interactive Capabilities Using the Heart Rate CourseCorrecting Inconsistent Heart Rate Readings How Hard Should I Exercise? Getting the Most Out of Your WorkoutHeart Rate Training Zone How Often Should I Exercise? How Long Should I Exercise?Cleaning the Equipment Changing the Battery in the Chest StrapMaintaining the Low Impact Treadmills Aligning the Running Belt Storing the Chest StrapAdjusting the Tension of the Belt Obtaining Service USA