ProForm PFTL57908.0 manual Assembly

Page 6

ASSEMBLY

To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor- mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key and your own Phillips screwdriver

,

.

adjustable wrench

, needlenose pliers

, scissors

, and rubber mallet

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assem- bly. Extra hardware may be included.

# 8 x 1"

#8 x 3/4"

#8 x 1/2"

5/16" x 1 3/4" Bolt (5)–4

Tek Screw (6)–4

Screw (1)–6

Screw (2)–2

# 8 x 3/4"

#10 x 3/4"

#8 x 1 1/2" Screw (3)–4

3/8" x 1 3/4" Bolt (7)–1

Tek Screw (13)–2

Screw (4)–4

 

#10 Star Washer

3/8" Star

3/8" Nut (10)–3

3/8" x 2" Bolt (9)–3

(12)–4

 

Washer (11)–4

 

 

Base Foot Spacer

 

3/8" x 4" Bolt (8)–4

 

 

 

(98)–2

 

 

 

 

 

6

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL57908.0 Serial No On the WEBTable of Contents Important Precautions Pulse sensor is not a medical devicePage Before YOU Begin Assembly Make sure that the power cord is unplugged Do not fully fold the Frame yetTighten the Nut the Wheel must turn freely Careful not to pinch the Wire Harness With a second Bolt Spacer 95, 3/8 x 4 Bolt 3/8 Star WasherTighten the Bolts yet Bolts yet Not Connected PROPERLY, the CON Sole MAY be Damaged When Screws before firmly tightening any of them Overtighten the Screws. Then, raiseRaise the Frame 48 to the position shown Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleMeasure your heart rate if desired. Before using Turn on the fan if desiredHOW to USE a Personal Trainer Quick ProgramHOW to Create Your OWN Quick Program Select a custom quick programHOW to USE Your OWN Quick Program Select a custom quick programsFollow your progress with the matrix and the displays Information Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PFTL57908.0 Key No. Qty Description101 Red Wire, M/F 102 #8 x 1/2 Console Ground Screw Exploded Drawing A-Model No. PFTL57908.0 R0908A Exploded Drawing B-Model No. PFTL57908.0 R0908A Exploded Drawing C-Model No. PFTL57908.0 R0908A Exploded Drawing D-Model No. PFTL57908.0 R0908A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents