ProForm PFTL57908.0 manual Bolts yet

Page 9

6.

Hold a Bolt Spacer (95) inside the lower end of

6

 

 

 

 

 

 

the Left Upright (77). Insert a 3/8" x 4" Bolt (8)

8

 

 

 

 

 

with a 3/8" Star Washer (11) into the Left

 

 

77

 

 

 

Upright and the Bolt Spacer. Repeat this step

 

 

 

 

 

 

with a second Bolt Spacer (95), 3/8" x 4" Bolt

 

11

 

 

 

 

 

(8), and 3/8" Star Washer (11).

 

 

94

 

 

 

Hold the Left Upright Spacer (94) and the Left

95

 

 

 

 

 

 

 

 

 

 

 

Upright (77) against the Base (96). Tighten the

 

 

 

 

 

 

3/8" x 4" Bolts (8) until the heads of the Bolts

 

 

 

 

 

 

 

touch the Left Upright; do not fully tighten the

93

95

96

 

 

 

 

Bolts yet.

 

 

 

 

Press a Base Cap (93) into the Base (96).

 

 

 

 

 

 

 

With the help of a second person, tip the tread-

 

 

 

 

 

 

 

mill so that the Base (96) is flat on the floor.

 

 

 

 

 

 

7. Attach two Top Handrail Spacers (64) to the

7

 

 

 

 

 

 

Uprights (77, 92) with two #8 x 3/4" Tek Screws

 

 

 

 

 

 

(13).

13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

64

 

 

77

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

64

 

 

 

 

 

 

 

92

 

 

8. Hold a Bottom Handrail Spacer (68) against the

8

 

 

 

 

 

 

Right Upright (92). Align the holes in the Bottom

 

 

 

 

 

 

Handrail Spacer with the holes in the Top

 

 

 

 

 

 

 

Handrail Spacer (64). Then, slide a Handrail

 

 

 

 

 

 

 

(80) onto the Handrail Spacers. Attach the

 

5

64

 

 

 

 

Handrail and Bottom Handrail Spacer to the

 

 

 

 

 

Right Upright with two 5/16" x 1 3/4" Bolts (5);

 

 

 

77

 

 

 

do not fully tighten the Bolts yet.

 

 

 

 

 

 

Repeat this step with the other Handrail (80)

 

80

68

 

 

 

 

and Bottom Handrail Spacer (68).

 

5

 

64

 

 

 

 

 

 

 

 

 

 

 

80

68

 

 

 

 

 

 

 

92

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model No. PFTL57908.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Pulse sensor is not a medical device Important PrecautionsPage Before YOU Begin Assembly Make sure that the power cord is unplugged Do not fully fold the Frame yetTighten the Nut the Wheel must turn freely Careful not to pinch the Wire Harness With a second Bolt Spacer 95, 3/8 x 4 Bolt 3/8 Star WasherTighten the Bolts yet Bolts yet Not Connected PROPERLY, the CON Sole MAY be Damaged When Overtighten the Screws. Then, raise Screws before firmly tightening any of themRaise the Frame 48 to the position shown Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerSelect the manual mode Insert the key into the consoleTurn on the fan if desired Measure your heart rate if desired. Before usingProgram HOW to USE a Personal Trainer QuickSelect a custom quick program HOW to Create Your OWN Quick ProgramHOW to USE Your OWN Quick Program Select a custom quick programsFollow your progress with the matrix and the displays Information Mode HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Top Problem The walking belt slows when walked onProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description Part LIST-Model No. PFTL57908.0101 Red Wire, M/F 102 #8 x 1/2 Console Ground Screw Exploded Drawing A-Model No. PFTL57908.0 R0908A Exploded Drawing B-Model No. PFTL57908.0 R0908A Exploded Drawing C-Model No. PFTL57908.0 R0908A Exploded Drawing D-Model No. PFTL57908.0 R0908A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents