ProForm PFTL14511.1 user manual Assembly, Make sure that the power cord is unplugged

Page 7

ASSEMBLY

•To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.

•Assembly requires two persons.

•Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you finish all assembly steps.

•After shipping, there may be an oily substance on the exterior of the incline trainer. This is nor- mal. If there is an oily substance on the incline trainer, wipe it off with a soft cloth and a mild, non-abrasive cleaner.

•To identify small parts, see page 6.

•Assembly requires the following tools:

the included hex key one adjustable wrench one Phillips screwdriver one pair of scissors

To avoid damaging parts, do not use power tools.

1. Make sure that the power cord is unplugged.	1
Place a piece of cardboard below the rear of the	1
Place a piece of cardboard below the rear of the
Frame (56) to protect the floor or carpet.
Attach the Left Wheel Cap (96) to the Base (94)
with two #8 x 3/4" Screws (2).		56
		56
Attach the Right Wheel Cap (not shown) to
the right side of the Base (94) in the same
way.	94
	94
	2
		96
		Cardboard
2. Pull the Upright Wire (81) and the Base Ground	2
Wire (110) through the indicated hole in the Base	2
Wire (110) through the indicated hole in the Base
(94).
Attach the Base Ground Wire (110) to the Base
(94) with a #8 x 1/2" Ground Screw (10).	Hole
	Hole
	81
		110
	10	94
	7

Image 7

Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL14511.1 Serial No Call TOLL-FREETable of Contents Important Precautions Page Before YOU Begin Part Identification Chart Make sure that the power cord is unplugged AssemblyAttach the Right Upright not shown See the inset drawing. Tie the wire tieBe careful not to pinch the Upright Wire Tighten the Screws yet. Note It may be helpBase Covers into place yet Page Then tighten them Wire. See the inset drawing. The connectorsShould slide together easily and snap into Again. if YOU do not Connect the CONPage Important See page 15 and plug Power cord. Next, see page 17 and turn onPower When the frame stops moving, removePage HOW to Connect the Power Cord Operation and AdjustmentUse a Surge Suppressor Features of the Console DiagramConsole HOW to USE the Touch Screen HOW to Turn on the PowerSole. Important Create an iFit Live account HOW to SET UP the ConsoleConnect to your wireless network Check for firmware updates Calibrate the incline systemHOW to USE the Manual Mode Measure your heart rate if desired When you are finished exercising, removePower cord. Important If you do not do Key from the consoleSelect an onboard workout HOW to USE AN Onboard WorkoutStart the workout Select the main menu. See on Select a set-a-goal workout HOW to USE a SET-A-GOAL WorkoutStart the workout. See on HOW to USE AN Ifit Live WorkoutHOW to USE the Equipment Settings Mode Find keycodes HOW to USE the Maintenance ModeExit the maintenance mode Calibrate the incline system of the treadmillExit the wireless network mode HOW to USE the Wireless Network ModeEnable Wi-Fi Set up and manage a wireless network connectionHOW to USE the Internet Browser HOW to USE the Stereo Sound SystemHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillSymptom The power turns off during use TroubleshootingTop View Symptom The walking belt slows when walked onPage Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description Part ListDescription Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT