ProForm PFTL14511.1 user manual

Page 31

SYMPTOM: The walking belt is off-center or slips when walked on

a.If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclock- wise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

a

b.If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws clockwise, 1/4 of a turn. When the walk- ing belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

b

SYMPTOM: The iFit Live mode does not function correctly

a.If the iFit Live mode is not functioning correctly, make sure that the treadmill has the most current firmware available (see step 3 on page 25).

SYMPTOM: The treadmill will not connect to the wireless network

a.Make sure that the wireless settings on your con- sole are correct (see step 4 on page 26).

b.Make sure that the settings for your wireless net- work are correct.

c.If you still have questions, see the front cover of this manual.

31

Image 31

Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL14511.1 Serial No Call TOLL-FREETable of Contents Important Precautions Page Before YOU Begin Part Identification Chart Make sure that the power cord is unplugged AssemblyAttach the Right Upright not shown See the inset drawing. Tie the wire tieBe careful not to pinch the Upright Wire Tighten the Screws yet. Note It may be helpBase Covers into place yet Page Then tighten them Wire. See the inset drawing. The connectorsShould slide together easily and snap into Again. if YOU do not Connect the CONPage Important See page 15 and plug Power cord. Next, see page 17 and turn onPower When the frame stops moving, removePage HOW to Connect the Power Cord Operation and AdjustmentUse a Surge Suppressor Features of the Console DiagramConsole HOW to USE the Touch Screen HOW to Turn on the PowerSole. Important Create an iFit Live account HOW to SET UP the ConsoleConnect to your wireless network Check for firmware updates Calibrate the incline systemHOW to USE the Manual Mode Measure your heart rate if desired When you are finished exercising, removePower cord. Important If you do not do Key from the consoleSelect an onboard workout HOW to USE AN Onboard WorkoutStart the workout Select the main menu. See on Select a set-a-goal workout HOW to USE a SET-A-GOAL WorkoutStart the workout. See on HOW to USE AN Ifit Live WorkoutHOW to USE the Equipment Settings Mode Find keycodes HOW to USE the Maintenance ModeExit the maintenance mode Calibrate the incline system of the treadmillExit the wireless network mode HOW to USE the Wireless Network ModeEnable Wi-Fi Set up and manage a wireless network connectionHOW to USE the Internet Browser HOW to USE the Stereo Sound SystemHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillSymptom The power turns off during use TroubleshootingTop View Symptom The walking belt slows when walked onPage Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description Part ListDescription Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT