ProForm pftl101110.0 user manual HOW to Fold and Move the Treadmill, HOW to Move the Treadmill

Page 27

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE Before folding the treadmill, adjust the incline to the lowest position. If you do not do this, you may damage the treadmill when you fold it. Remove the key and unplug the power cord. CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill.

1.Hold the metal frame firmly in the location shown by the arrow at the right. CAUTION: To decrease the pos- sibility of injury, do not lift the treadmill by the plastic foot rails. To raise the frame, bend your legs, keep your back straight, and lift with your legs rather than your back. Raise the frame about halfway to the vertical position.

2.Raise the frame until the latch knob locks into the storage position. Make sure that the latch knob is locked in the storage position.

To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of di- rect sunlight. Do not leave the treadmill in the storage position in temperatures above 85° F (30° C).

HOW TO MOVE THE TREADMILL

Before moving the treadmill, convert it to the storage posi- tion as described above. Make sure that the latch knob is locked in the storage position.

1.Hold the handrails and place one foot against one of the wheels.

2.Tip the treadmill back until it rolls freely on the wheelsNever. Carefully move the treadmill to the desired location. move the treadmill without tipping it back. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not attempt to move the treadmill over an uneven surface.

3.Place one foot against a wheel, and carefully lower the treadmill until it is resting in the storage position.

Frame

Frame

Latch Knob

Handrail

Wheel

27

Image 27
Contents On the WEB QUESTIONS?Model No. PFTL10110.0 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Page Power Lines Ground Standoff Service Clamp Before YOU Begin Assembly Make sure that the power cord is unpluggedFirmly tighten the Bolts Until the treadmill is completely assembled Is more stable. Do not fully fold the FrameRaise the Frame 55 to the position shown Start all four Bolts before tightening any of them Attach the Left Upright Sleeve not shown in the same way Make sure that no wires are pinched. See HOW to Connect AN Antenna Ohm Flat WireOhm Catv Cable Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt This manual. iFit cards are also available at select stores Console Diagram Features of the ConsoleHOW to USE the Manual Mode HOW to Turn on the PowerPage Start the walking belt HOW to USE a Preset ProgramHOW to USE a Pulse Program Caution If you have heart prob See on HOW to Create a Custom Program HOW to USE a Custom Program HOW to USE AN Ifit Card HOW to USE the Stereo Sound System Press the Power button again and add or remove channels Information ModeOptional Chest Pulse Sensor HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Important The treadmill is notTop Problem The walking belt slows when walked onUnplug the Power CORD. If the walking belt Key and Unplug the Power CORD. UsingProblem Television reception is poor Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description R0110AQty Exploded Drawing A-Model No. PFTL10110.0 R0110A Exploded Drawing B-Model No. PFTL10110.0 R0110A Exploded Drawing C-Model No. PFTL10110.0 Exploded Drawing D-Model No. PFTL10110.0 R0110A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT