ProForm pftl101110.0 user manual Power Lines Ground Standoff Service Clamp

Page 5

32.Upon completion of any service or repairs to the treadmill or the television, ask the service technician to perform safety checks to con- firm that the unit is in proper operating condi- tion.

Use No. 10 AWG (5.3 mm2) copper, No. 8 AWG (8.4 mm2) aluminum, No. 17 AWG (1.0 mm2) copper-clad steel or bronze wire, or larger as a ground wire.

Secure an antenna lead-in and ground wires to the house with stand-off insulators spaced from 4 to 6 feet (1.22 to 1.83 m) apart.

Mount an antenna discharge unit as close as possible to where the lead-in enters the house.

Use a jumper wire not smaller than No. 6 AWG (13. 3mm2) copper, or the equivalent when a separate antenna-grounding elec- trode is used. See NEC Section 810-21 (j).

Note to CATV system installer: This reminder is provided to call the CATV system installerʼs at- tention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particu- lar, specifies that the cable ground shall be con- nected to the grounding system of the building, as close to the point of cable entry as practical.

Power Lines

 

Ground

Standoff

 

 

Service

 

Clamp

Insulators

 

To External 75 Ohm

Mast

 

Entrance

 

Antenna

Conductors

 

Terminal of Treadmill

 

Service

 

Ground

Lead-in Wire

Entrance

 

 

Antenna

Equipment

 

Wire

Discharge Unit

Power Service Grounding

Ground

Bonding

Ground Wire

Electrode System (e.g.

Ground

 

Interior Metal Water Pipe)

Clamps

Jumper

Clamps

 

 

 

Optional Antenna Grounding Electrode Driven 8

 

 

Feet (2.44 m) Into The Earth (If Required By Local

 

 

Codes). See NEC Section 810–21 (f).

SAVE THESE INSTRUCTIONS

 

5

Image 5
Contents Model No. PFTL10110.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Page Power Lines Ground Standoff Service Clamp Before YOU Begin Firmly tighten the Bolts AssemblyMake sure that the power cord is unplugged Until the treadmill is completely assembled Is more stable. Do not fully fold the FrameRaise the Frame 55 to the position shown Start all four Bolts before tightening any of them Attach the Left Upright Sleeve not shown in the same way Make sure that no wires are pinched. See Ohm Catv Cable HOW to Connect AN AntennaOhm Flat Wire PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord This manual. iFit cards are also available at select stores Console Diagram Features of the ConsoleHOW to USE the Manual Mode HOW to Turn on the PowerPage Start the walking belt HOW to USE a Preset ProgramHOW to USE a Pulse Program Caution If you have heart prob See on HOW to Create a Custom Program HOW to USE a Custom Program HOW to USE AN Ifit Card HOW to USE the Stereo Sound System Press the Power button again and add or remove channels Information ModeOptional Chest Pulse Sensor HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingImportant The treadmill is not Compatible with GFCI-equipped outletsUnplug the Power CORD. If the walking belt Problem The walking belt slows when walked onKey and Unplug the Power CORD. Using TopProblem Television reception is poor Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description R0110AQty Exploded Drawing A-Model No. PFTL10110.0 R0110A Exploded Drawing B-Model No. PFTL10110.0 R0110A Exploded Drawing C-Model No. PFTL10110.0 Exploded Drawing D-Model No. PFTL10110.0 R0110A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty