ProForm pftl101110.0 user manual Troubleshooting, Important The treadmill is not

Page 29

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 14.

IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch pro-

 

trudes as shown, the circuit breaker has tripped. To

 

 

reset the circuit breaker, wait for five minutes and

Tripped

Reset

then press the switch to the reset position.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait

for five minutes and then press the switch to the reset position.

 

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five

minutes, and then plug it back in.

 

 

c. Remove the key from the console. Reinsert the key into the console.

 

d. If the treadmill still will not run, please see the front cover of this manual.

 

PROBLEM: The displays of the console do not function properly

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

POWER CORD. Next, carefully lower the Uprights

 

(85). Remove the two indicated #8 x 3/4" Tek Screws

 

 

(32). Note: A Phillips screwdriver with a shaft at least

 

 

8 in. (20 cm) long is needed.

 

 

 

85

32

Raise the Uprights (85) to the vertical position. Remove the three #8 x 3/4" Screws (7) from the Motor Hood (33), and carefully pivot the Motor Hood off.

85

33

7

 

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Model No. PFTL10110.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Page Power Lines Ground Standoff Service Clamp Before YOU Begin Firmly tighten the Bolts AssemblyMake sure that the power cord is unplugged Until the treadmill is completely assembled Is more stable. Do not fully fold the FrameRaise the Frame 55 to the position shown Start all four Bolts before tightening any of them Attach the Left Upright Sleeve not shown in the same way Make sure that no wires are pinched. See Ohm Catv Cable HOW to Connect AN AntennaOhm Flat Wire PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord This manual. iFit cards are also available at select stores Console Diagram Features of the ConsoleHOW to USE the Manual Mode HOW to Turn on the PowerPage Start the walking belt HOW to USE a Preset ProgramHOW to USE a Pulse Program Caution If you have heart prob See on HOW to Create a Custom Program HOW to USE a Custom Program HOW to USE AN Ifit Card HOW to USE the Stereo Sound System Press the Power button again and add or remove channels Information ModeOptional Chest Pulse Sensor HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingImportant The treadmill is not Compatible with GFCI-equipped outletsUnplug the Power CORD. If the walking belt Problem The walking belt slows when walked onKey and Unplug the Power CORD. Using TopProblem Television reception is poor Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description R0110AQty Exploded Drawing A-Model No. PFTL10110.0 R0110A Exploded Drawing B-Model No. PFTL10110.0 R0110A Exploded Drawing C-Model No. PFTL10110.0 Exploded Drawing D-Model No. PFTL10110.0 R0110A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents