ProForm 480 CX user manual Troubleshooting, Problem The power turns off during use

Page 26

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 11). If an exten- sion cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5 m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d.Check the on/off switch located on the treadmill near the power cord. The switch must be in the “on” position.

PROBLEM: The power turns off during use

c

 

Tripped

Reset

d

On

 

 

Position

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.Make sure that the on/off switch is in the “on” position (see d. above).

e.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. With the help of a second person, carefully tip the Uprights (84) down as shown. Next, re- move the three Screws (3) and the three 3/4” Screws (83). Note: A phillips screwdriver with a shaft at least 5” long is required.

a

3

83

84

 

 

 

 

3

26

Image 26
Contents Model No. PATL40906.0 Serial No Please Contact OUR CUS- Tomer Service Department DirectlyQUESTIONS? Table of Contents Important Precautions Page Right Side Before YOU BeginBack Assembly Make sure that the power cord is unpluggedHandrail Bolts and then firmly tighten them No Screws HOW to Fold and Move the Treadmill Out of the Shock. Be careful to avoid losing Shock PinSmall Screws Wire Cylinder PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeWhenkey. you are finished exercising, remove Measure your heart rate if desiredTurn on the fan if desired HOW to USE a Trainer Program Select a trainer programSelect a heart rate program HOW to USE a Heart Rate ProgramPut on the optional chest pulse sensor Follow your progress with the display Audio Cable HOW to Connect Your MP3 Player or CD PlayerHOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Press the Play button on your MP3 player, CD Player, or VCRMeasure your heart rate if desired Return to the treadmill and stand on the foot Directly from OUR WEB SiteFollow the on-line instructions to start Program Information Mode Optional Chest Pulse SensorHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopWorkout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part LIST-Model No. PATL40906.0 Key No. Qty DescriptionPage Model No R0906A Exploded DRAWING-Model No. PATL40906.0 Exploded DRAWING-Model No. PATL40906.0 Goodfamily, Inc Ordering Replacement PartsLimited Warranty