ProForm 480 CX user manual Assembly, Make sure that the power cord is unplugged

Page 6

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex keys,

your own phillips screwdriver

, and your

own rubber mallet

.

 

 

For help identifying the assembly hardware, see the drawings below. The number in parentheses below each drawing is the key number of the part, from the PART LIST on pages 30 and 31. The number following the paren- theses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it has been pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly.

1” Tek Screw

Silver Ground

Screw (3)–11

(22)–4

Screw (33)–1

Star Washer (8)–8

Handrail Bolt/Extension Leg Bolt (64)–8

1.Make sure that the power cord is unplugged.

With the help of a second person, carefully tip the treadmill onto its left side as shown. Partially fold the Frame (58) so the treadmill is more sta- ble. Do not fully fold the treadmill until it is completely assembled.

Insert an Extension Leg (89) into the base of the Upright (84) as shown. Note: Be careful not to pinch the Upright Wire Harness (77) in the base of the Upright. To fully insert the Extension Leg, it may be necessary to tap on it with a mallet. Next, insert two Extension Leg Bolts (64) with Star Washers (8) into the bottom of the Extension Leg, and firmly tighten the Extension Leg Bolts.

1

 

89

77

 

8

 

64

 

58

6

Image 6
Contents Please Contact OUR CUS- Tomer Service Department Directly QUESTIONS?Model No. PATL40906.0 Serial No Table of Contents Important Precautions Page Before YOU Begin BackRight Side Assembly Make sure that the power cord is unpluggedHandrail Bolts and then firmly tighten them No Screws HOW to Fold and Move the Treadmill Out of the Shock. Be careful to avoid losing Shock PinSmall Screws Wire Cylinder Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Turn on the fan if desiredWhenkey. you are finished exercising, remove HOW to USE a Trainer Program Select a trainer programHOW to USE a Heart Rate Program Put on the optional chest pulse sensorSelect a heart rate program Follow your progress with the display HOW to Connect Your MP3 Player or CD Player HOW to Connect Your Portable StereoAudio Cable HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Press the Play button on your MP3 player, CD Player, or VCRMeasure your heart rate if desired Directly from OUR WEB Site Follow the on-line instructions to start ProgramReturn to the treadmill and stand on the foot Information Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopWorkout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part LIST-Model No. PATL40906.0 Key No. Qty DescriptionPage Model No R0906A Exploded DRAWING-Model No. PATL40906.0 Exploded DRAWING-Model No. PATL40906.0 Ordering Replacement Parts Limited WarrantyGoodfamily, Inc