JVC RX-F10S manual Adjusting speaker output level, Adjusting the effect level for DSP modes-EFFECT

Adjusting speaker output level

•SUBWFR LVL (subwoofer output level),

•FRONT L LVL (left front speaker output level),

•FRONT R LVL (right front speaker output level),

•CENTER LVL (center speaker output level),

•SURR L LVL (left surround speaker output level),

•SURR R LVL (right surround speaker output level),

•S BACK LVL (surround back speaker output level)

You can adjust the speaker output levels.

Adjust all the speakers’ output levels so that you can listen to the sounds from all the speakers at the same level.

•Once you have made an adjustment, it is memorized for each source.

Adjustable range: –10 (dB) to +10 (dB) (in 1 step intervals)

Initial setting: 0 (dB) for all speakers

NOTES

•If you have selected “NO” for a speaker (see page 18), the output level for the corresponding speaker is not adjustable.

•While using the headphones, you can adjust only the left and right front speakers’ output level.

•If you change one of these settings (except the subwoofer output level) manually, the distance and output level set manually will be applied instead of those set by using Smart Surround Setup.

From the remote control:

Set the mode selector to “AUDIO/TV/VCR/DBS.”

Adjusting the sound parameters for the Surround/DSP modes

You can adjust the Surround/DSP sound parameters to your

preference.

• For details about the Surround/DSP modes, see pages 27 to 31.

Adjusting the effect level for DSP modes—EFFECT

This setting is available only when one of the DSP modes (except ALL CH ST.) is in use. To activate DSP mode, see page 31.

•Once you have made an adjustment, it is memorized for each DSP mode.

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting: EFFECT 3

As the number increases, the effect becomes stronger. Normally, select “3.”

Adjusting the panorama control for Pro Logic II Music—PANORAMA

This setting is available only when Pro Logic II Music is in use. To activate Pro Logic II Music, see page 31.

•Once you have made an adjustment, it is memorized until you change the setting.

•You cannot use the remote control for this setting.

PANORAMA ON Select to add “wraparound” sound effect with

1Press TEST TONE to check the speakers’ output balance.

“TEST L” starts flashing on the display, and a test tone comes out of the speakers in the following order:

L	C
	R

SW

LS RS

SB

2Adjust the speaker output levels.

2

1, 3

side-wall image.
PANORAMAOFF Select to listen to originally recorded sound.	adjustments
Adjusting the center tone—CENTER TONE
Initial setting: PANORAMAOFF
• If you have set “CENTER SPK” to “NO” (see page 18), the	Sound
This setting is available when one of the Surround/DSP modes is
in use.
center tone is not adjustable.
• This setting is common to all Surround modes, and is
memorized separately for DSP modes.
Adjustable range: 1 to 5 (in 1 step intervals)
Initial setting: CNT TONE 3
As the number increases, the dialogue becomes stronger.
Normally, select “3.”

•If no adjustment is made for about one minute, the test tone will stop.

To adjust the left front speaker level (L), press

FRONT L +/–.

To adjust the right front speaker level (R), press

FRONT R +/–.

To adjust the center speaker level (C), press

CENTER +/–.

To adjust the left surround speaker level (LS), press

SURR L +/–.

To adjust the right surround speaker level (RS), press

SURR R +/–.

To adjust the surround back speaker level (SB), press

S.BACK +/–.

To adjust the subwoofer level (SW), press SUBWFR +/–.

3Press TEST TONE again to stop the test tone.

NOTES

•You can adjust the speaker output levels without the test tone.

•No test tone comes out of the speakers for which the speaker setting is set to “NO” (see page 18).

•No test tone is available when the headphone is in use or “DVD MULTI” is selected.

•When the center tone is set to other than “CNT TONE 3,” the C.TONE indicator lights up on the display.

From the remote control:

Set the mode selector to “AUDIO/TV/VCR/DBS.”

To adjust the effect level:

Press SOUND, then press EFFECT

repeatedly.

To adjust the center tone:

Press SOUND, then press C.TONE repeatedly.

NOTE

After pressing SOUND, the numeric buttons work for sound adjustments. To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation; otherwise, the remote control may not work as you intend.

23