JVC RX-F10S manual Adjusting the sound parameters for, Surround/DSP modes

Page 70

Adjusting speaker output level

SUBWFR LVL (subwoofer output level),

FRONT L LVL (left front speaker output level),

FRONT R LVL (right front speaker output level),

CENTER LVL (center speaker output level),

SURR L LVL (left surround speaker output level),

SURR R LVL (right surround speaker output level),

S BACK LVL (surround back speaker output level)

You can adjust the speaker output levels.

Adjust all the speakers’ output levels so that you can listen to the sounds from all the speakers at the same level.

Once you have made an adjustment, it is memorized for each source.

Adjustable range: –10 (dB) to +10 (dB) (in 1 step intervals)

Initial setting: 0 (dB) for all speakers

NOTES

If you have selected “NO” for a speaker (see page 18), the output level for the corresponding speaker is not adjustable.

While using the headphones, you can adjust only the left and right front speakers’ output level.

If you change one of these settings (except the subwoofer output level) manually, the distance and output level set manually will be applied instead of those set by using Smart Surround Setup.

From the remote control:

Set the mode selector to “AUDIO/TV/VCR/DBS.”

Adjusting the sound parameters for

preference.

English

the Surround/DSP modes

 

You can adjust the Surround/DSP sound parameters to your

 

• For details about the Surround/DSP modes, see pages 27 to 31.

 

Adjusting the effect level for DSP modes—EFFECT

 

This setting is available only when one of the DSP modes (except

 

ALL CH ST.) is in use. To activate DSP mode, see page 31.

 

Once you have made an adjustment, it is memorized for each DSP mode.

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting: EFFECT 3

As the number increases, the effect becomes stronger.

Normally, select “3.”

Adjusting the panorama control for Pro Logic II Music—PANORAMA

This setting is available only when Pro Logic II Music is in use. To activate Pro Logic II Music, see page 31.

Once you have made an adjustment, it is memorized until you change the setting.

You cannot use the remote control for this setting.

PANORAMA ON Select to add “wraparound” sound effect with

1Press TEST TONE to check the speakers’ output balance.

“TEST L” starts flashing on the display, and a test tone comes out of the speakers in the following order:

L

C

R

SW

LS

RS

SB

2Adjust the speaker output levels.

2

1, 3

side-wall image.

 

PANORAMAOFF Select to listen to originally recorded sound.

adjustments

 

Adjusting the center tone—CENTER TONE

Initial setting: PANORAMAOFF

 

• If you have set “CENTER SPK” to “NO” (see page 18), the

Sound

This setting is available when one of the Surround/DSP modes is

 

in use.

 

center tone is not adjustable.

 

• This setting is common to all Surround modes, and is

 

memorized separately for DSP modes.

 

Adjustable range: 1 to 5 (in 1 step intervals)

 

Initial setting: CNT TONE 3

 

As the number increases, the dialogue becomes stronger.

 

Normally, select “3.”

 

If no adjustment is made for about one minute, the test tone will stop.

To adjust the left front speaker level (L), press

FRONT L +/–.

To adjust the right front speaker level (R), press

FRONT R +/–.

To adjust the center speaker level (C), press

CENTER +/–.

To adjust the left surround speaker level (LS), press

SURR L +/–.

To adjust the right surround speaker level (RS), press

SURR R +/–.

To adjust the surround back speaker level (SB), press

S.BACK +/–.

To adjust the subwoofer level (SW), press SUBWFR +/–.

3Press TEST TONE again to stop the test tone.

NOTES

You can adjust the speaker output levels without the test tone.

No test tone comes out of the speakers for which the speaker setting is set to “NO” (see page 18).

No test tone is available when the headphone is in use or “DVD MULTI” is selected.

When the center tone is set to other than “CNT TONE 3,” the C.TONE indicator lights up on the display.

From the remote control:

Set the mode selector to “AUDIO/TV/VCR/DBS.”

To adjust the effect level:

Press SOUND, then press EFFECT

repeatedly.

To adjust the center tone:

Press SOUND, then press C.TONE repeatedly.

NOTE

After pressing SOUND, the numeric buttons work for sound adjustments. To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation; otherwise, the remote control may not work as you intend.

23

Image 70
Contents RX-F10S For Customer UseFor Canada/pour le Canada For Canada/pour Le CanadaFor U.S.A Table of Contents Remote control Parts identificationDisplay window Front panelRear panel Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedAM antenna connection Connecting the FM and AM antennasFM antenna connection Connecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferNot supplied Connecting video componentsTurn off all components before making connections Only for DVD recorder To S-video inputGreen Blue Red About DVD MultiWhite Connecting a DBS tuner Connecting a TVDigital input terminals Connecting the power cordDigital connection Digital output terminalSelecting the analog or digital input mode Turn on the powerTo turn off the power into standby Basic operationsSelecting the digital decode mode Adjust the volumeListening with headphones Press TV Direct Adjusting the subwoofer audio positionActivating TV Direct AUDIO/TV/VCR/DBSSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Turning off the sounds temporarilyFrom the remote control only Basic settingsTake your position where you listen to Sound Basic setting items Setting the speakers Operating procedureSetting subwoofer information-SUBWOOFER Setting subwoofer output-SUBWFR OUT Setting bass soundSetting the speaker distance Setting the crossover frequency-CROSS OverUsing the Midnight mode Selecting the main or sub channelVCR S/C Auto SR onAuto Sroff VCR CompntPress Adjust Sound adjustmentsBasic adjustment items Turn Multi JOG to adjust the selected itemAdjusting the effect level for DSP modes-EFFECT Adjusting speaker output levelAdjusting the center tone-CENTER Tone Selecting the subwoofer sound phase-SBWFR Adjusting the bass soundsAttenuating the input signal-INPUT ATT Reinforcing the bass-BASS BoostTo store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsFrom the remote control Press FM/AM to select the band Selecting the FM reception modeTo tune in a preset station Press Tuner PresetIntroducing the Surround modes Creating realistic sound fieldsReproducing theater ambience Dolby DigitalAbout other digital signals 3D Headphone modeDTS Introducing the DSP modes All Channel Stereo mode ALL CH STDigital Acoustic Processor DAP modes Using the Surround/DSP modes Virtual Surround BackSelect and play any source other than DVD Multi Turn Multi JOG to select the Surround/DSP mode you wantTo cancel Surround/DSP modes Press SurroundConnections 2 Video cable connection AV Compu Link remote control systemConnections 1 AV Compu Link connection CaseAutomatic power on/off Connecting procedureAutomatic selection of TV’s input mode One-touch video playChannel + Operating other JVC productsVCR REC PauseTOP MENU/MENU DVD recorder or DVD playerDVR/DVD ZoomRelease TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Try to operate your TV by pressing TVTry to operate your VCR by pressing VCR Changing the transmittable signals for operating a VCRRelease VCR Manufacturers’ codes for VCRManufacturers’ codes for DBS tuner Release DBSManufacturers’ codes for Catv converter Release DVR/DVDTroubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM tunerLimited Warranty Authorized Service Centers RX-F10S Home Theater Receiver Recepteur Pour Cinema Maison Mises en garde, précautions et indications diverses English Parts identification Front panel Getting started Connecting the FM and AM antennas Connecting the speakers Connecting video components Green Blue Red White Red DBS tuner Composite video cable not supplied You can connect any digital componens which have an optical Basic operations Adjust the volume Adjusting the subwoofer audio PositionTurning off the sounds temporarily Basic settings Basic setting items 12 cm Setting the crossover frequency-CROSS Over Dual Mono Setting Auto Surround-AUTO Surrnd Sound adjustments Adjusting the effect level for DSP modes-EFFECT Adjusting the sound parameters forSurround/DSP modes Adjusting the bass sounds From the remote control only Press the numeric buttons 1 10, +10 to Plii Movie Pro Logic II Movie Plii Movie and Pro Logic II Music PliiPlii Music English Introducing the DSP modes EX/ES setting SML/LRG AUTO/ONActivating the Surround/DSP modes AV Compu Link remote control system Connecting procedure Operating other JVC products DVD/CARD CancelReturn DimmerManufacturers’ Operating otherProducts English Release DBS Troubleshooting Power Requirements AC 120 V , 60 Hz Power Consumption EN, FR Victor Company of JAPAN, Limited 0404MWMMDWJEIN

RX-F10S specifications

The JVC RX-F10S is an impressive home theater receiver that embodies a blend of power, versatility, and advanced technology. Designed to enhance the audio-visual experience, this receiver offers a suite of features that cater to both casual listeners and audiophiles alike.

At the heart of the RX-F10S is its robust amplification system, delivering a powerful output that ensures high-quality sound reproduction across a wide range of frequencies. With multiple channels for surround sound support, it allows users to create an immersive audio environment, perfect for movie-watching or music enjoyment. The receiver supports various surround sound formats, such as Dolby Digital and DTS, enabling a cinematic experience right in the comfort of one's living room.

One of the standout features of the RX-F10S is its connectivity options. It is equipped with multiple HDMI inputs that support the latest 4K Ultra HD and HDR pass-through. This ensures compatibility with the latest gaming consoles, Blu-ray players, and streaming devices, providing future-proofing for your entertainment setup. In addition to HDMI, the receiver also includes optical and coaxial digital inputs, along with several analog inputs, providing flexibility in connecting various audio sources.

The RX-F10S is designed with user convenience in mind. Its intuitive on-screen interface simplifies the setup process and allows users to easily navigate through settings and options. The inclusion of a remote control further enhances usability, making it easy to switch between audio sources and adjust sound settings without getting up.

Another notable aspect of the JVC RX-F10S is its compatibility with wireless technologies. It features built-in Bluetooth that allows for seamless streaming from smartphones, tablets, and other compatible devices. This adds an extra layer of convenience, enabling users to enjoy their favorite music without the hassle of physical connections.

In terms of sound customization, the RX-F10S includes an equalizer that allows listeners to adjust their audio preferences according to their taste or the acoustics of their room. This level of personalization is crucial for those who seek a tailored listening experience.

Overall, the JVC RX-F10S is a versatile home theater receiver that combines powerful performance with a wide array of connectivity options and advanced features. Its ability to deliver high-quality sound while being user-friendly makes it an excellent choice for anyone looking to upgrade their home entertainment setup. Whether you are watching movies, playing games, or listening to music, the RX-F10S is poised to elevate your audio experience to new heights.