JVC RX-F10S manual Adjust the volume

3 Adjust the volume

To increase the volume, turn MASTER VOLUME control clockwise (or press VOLUME + on the remote control).

To decrease the volume, turn MASTER VOLUME control counterclockwise (or press VOLUME – on the remote control).

•When you adjust the volume, the volume level indication appears on the display for a while.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

CAUTION:

Always set the volume to the minimum before starting any sources. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

NOTE

The volume level can be adjusted within the range of “0” (minimum) to “50” (maximum).

Listening with headphones

You can enjoy not only stereo software but also multi-channel software through the headphones. (Sounds are down-mixed to the front channels while playing multi-channel software.)

Connect a pair of headphones to the PHONES jack on the front panel to activate the HEADPHONE mode.

The HP (headphone) indicator lights up on the display.

•You can also enjoy the Surround/DSP mode through the headphones—3D HEADPHONE mode. For details, see pages 28 and 29.

•Disconnecting a pair of headphones from the PHONES jack cancels the HEADPHONE (or 3D HEADPHONE) mode and activates the speakers.

CAUTION:

Be sure to turn down the volume:

•Before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.

•Before removing headphones, as high volume may output from the speakers.

Selecting the digital decode mode

If the following symptoms occur while playing Dolby Digital or DTS software with “DGTL AUTO” selected (see page 12), follow the procedure below:

•Sound does not come out at the beginning of playback.

•Noise comes out while searching for or skipping chapters or tracks.

From the remote control ONLY:

Press SOUND, then press DECODE to select “DGTL D.D.” or “DGTL DTS.”

•Each time you press DECODE, the digital decode mode changes as follows:

EQ C.TONE		VIRTUAL SB AUDIO P. BASS				TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L		C	R	PL	ATT
DOLBY D	S . WFR LFE				NEO : 6	HP
DTS AAC					DSP 3D	MHz
	LS	SB		RS
96 / 24					AUTO SR	kHz

DGTL AUTO DGTL D.D.

DGTL DTS (Back to the beginning)

•To play back software encoded with Dolby Digital, select “DGTL D.D.”

•To play back software encoded with DTS, select “DGTL DTS.”

NOTES

•When you turn off the power or select another source,

“DGTL D.D.” or “DGTL DTS” is canceled and the digital decode mode is automatically reset to “DGTL AUTO.”

•After pressing SOUND, the numeric buttons work for sound adjustments. To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation; otherwise, the remote control may not work as you intend.

The following digital signal format indicators on the display indicate what type of signal comes into the receiver.

LPCM: Lights up when Linear PCM signal comes in.

DOLBY D: • Lights up when Dolby Digital signal comes in.

•Flashes when “DGTL D.D.” is selected for any software other than Dolby Digital.

DTS: • Lights up when conventional DTS signal comes in.

•Flashes when “DGTL DTS” is selected for any software other than DTS.

DTS 96/24: Lights up when DTS 96/24 signal comes in.

NOTE

When “DGTL AUTO” cannot recognize the incoming signal, no digital signal format indicator lights up on the display.

English

Basic operations

13