JVC RX-F10S Selecting the FM reception mode, To tune in a preset station, Press Tuner Preset

Tuner operations

3Press the numeric buttons (1 – 10, +10) to select a channel number while the channel number position is flashing.

•For channel number 5, press 5.

•For channel number 15, press +10, then 5.

•For channel number 30, press +10, +10, then 10.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

4Press MEMORY again while the selected channel number is flashing on the display.

The selected channel number stops flashing.

The station is assigned to the selected channel number.

5Repeat steps 1 to 4 until you store all the stations you want.

To erase a stored preset station

Storing a new station on a used channel number erases the previously stored one.

To tune in a preset station

From the remote control:

1Press FM/AM to select the band.

The last received station of the selected band is tuned in and the numeric buttons now work for tuner operations.

•Each time you press the button, the band alternates between FM and AM.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

2Press the numeric buttons (1 – 10, +10) to select a preset channel number.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

•For channel number 5, press 5.

•For channel number 15, press +10, then 5.

•For channel number 30, press +10, +10, then 10.

On the front panel:

2 1, 3

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

1Turn SOURCE SELECTOR to select “FM” or “AM.”

The last received station of the selected band is tuned in.

2Press TUNER PRESET.

“P” appears on the display and MULTI JOG now works for selecting preset channels.

3Turn MULTI JOG to select a preset channel number while “P” appears on the display.

•To increase the preset channel numbers, turn MULTI JOG clockwise.

•To decreases the preset channel numbers, turn MULTI JOG counterclockwise.

EQ C.TONE		VIRTUAL SB AUDIO P. BASS			TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE
LPCM	L	C	R	PL	ATT
DOLBY D	S . WFR LFE			NEO : 6	HP
DTS AAC				DSP 3D	MHz
	LS	SB	RS
96 / 24				AUTO SR	kHz

Selecting the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, you can change the FM reception mode while receiving an FM broadcast.

•You can store the FM reception mode for each preset station (see page 25).

From the remote control ONLY:

While listening to an FM station, press FM MODE.

•Each time you press the button, the FM reception mode alternates between “AUTO MUTING” and “MONO.”

AUTO MUTING	Normally select this.
	When a program is broadcast in stereo,
	you will hear stereo sound; when in
	monaural, you will hear monaural sound.
	This mode is also useful to suppress
	static noise between stations. The AUTO
	MUTING indicator lights up on the display.
MONO	Select this to improve the reception (but
	stereo effect will be lost).
	In this mode, you will hear noise while
	tuning in to the stations. The AUTO
	MUTING indicator goes off from the
	display. (The ST indicator also goes off.)

Initial setting: AUTO MUTING

26