JVC RX-F10S manual Setting the crossover frequency-CROSS Over

Page 66

Setting the speaker distance

The distance from your listening point to the speakers is one of the important elements to obtain the best possible sound effect from the Surround/DSP modes.

By referring to the speaker distance, the receiver automatically sets the delay time of the sound through each speaker so that sounds through all the speakers can reach you at the same time.

7Measuring unit—DIST UNIT

Select which measuring unit you use.

UNIT :meter Select to set the distance in meters.

UNIT : feet Select to set the distance in feet.

Initial setting: UNIT :meter

7Speaker distance—

FRNT L DIST (for the left front speaker), FRNT R DIST (for the right front speaker), CENTER DIST (for the center speaker), SURR L DIST (for the left surround speaker), SURR R DIST (for the right surround speaker), S BACK DIST (for the surround back speaker)

Adjustable range: 0.3 m to 9.0 m in 0.3 m intervals (1 ft to 30 ft in 1 ft intervals)

Initial setting: 3.0 m (10 ft) for all speakers

If you have used Smart Surround Setup on page 16, this setting is not required.

Setting bass sound

Setting subwoofer output—SUBWFR OUT

You can select the type of the signal which can be transmitted through the subwoofer. In other words, you can determine whether or not the bass elements of the front speaker channels are transmitted through the subwoofer regardless of the front speaker size setting (either “SML” or “LRG”).

SW: LFE

Select to emit only the LFE signals (while

 

playing Dolby Digital and DTS software) or

 

the bass elements of the “SML (small)” front

 

speakers (while playing any source other than

 

above).

 

 

SW:LFE+MAIN

Select to always emit the bass elements of

 

the front speaker channels (MAIN). While

 

playing Dolby Digital and DTS software, the

 

bass elements and the LFE signals are both

 

emitted.

 

 

Initial setting: SW: LFE

NOTE

When “SUBWOOFER” is set to “SUBWFR : NO” (see page 18), this function is not available.

Setting the crossover frequency—CROSS OVER

English

C

L

LS

SB

R

3.3 m

(11 ft)

3.0 m

(10 ft)

2.7 m

(9 ft)

2.4m (8 ft)

2.1m (7 ft)

RS

Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this receiver automatically reallocates the bass sound elements assigned to the small speaker to the large speakers.

To use this function properly, set this crossover frequency level according to the size of the small speaker connected.

If you have selected “LRG (large)” for all speakers (see page 18), this function will not take effect (“CROSS: OFF” appears).

CROSS: 80Hz Select when the cone speaker unit built in the speaker is about 12 cm.

CROSS:100Hz Select when the cone speaker unit built in the speaker is about 10 cm.

CROSS:120Hz Select when the cone speaker unit built in the speaker is about 8 cm.

CROSS:150Hz Select when the cone speaker unit built in the speaker is about 6 cm.

CROSS:200Hz Select when the cone speaker unit built in the

speaker is less than 5 cm.

Basic settings

In this case, set the distance as follows:

Left front speaker (L):

“FL D : 3.0m (10ft)”

Right front speaker (R):

“FR D : 3.0m (10ft)”

Center speaker (C):

“C D : 3.0m (10ft)”

Left surround speaker (LS):

“LS D : 2.7m (9ft)”

Right surround speaker (RS):

“RS D : 2.7m (9ft)”

Surround back speaker (SB):

“SB D : 2.4m (8ft)”

NOTES

You cannot set the speaker distance for the speakers you have set to “NO.”

If you change one of these settings manually, the distance and output level manually set will be applied instead of those set by using Smart Surround Setup.

Initial setting: CROSS:150Hz

NOTE

Crossover frequency is not valid for the HEADPHONE and 3D HEADPHONE modes.

Setting the low frequency effect attenuator—LFE

ATT

If the bass sound is distorted while playing back software encoded with Dolby Digital or DTS, set the LFE level to eliminate distortion.

• This function takes effect only when the LFE signals come in.

LFE : 0dB Normally select this.

LFE :–10dBSelect when the bass sound is distorted.

Initial setting: LFE : 0dB

19

Image 66
Contents RX-F10S For Customer UseFor Canada/pour Le Canada For Canada/pour le CanadaFor U.S.A Table of Contents Remote control Parts identificationFront panel Display windowRear panel Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedConnecting the FM and AM antennas AM antenna connectionFM antenna connection Connecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferNot supplied Connecting video componentsTurn off all components before making connections Only for DVD recorder To S-video inputGreen Blue Red About DVD MultiWhite Connecting a DBS tuner Connecting a TVDigital input terminals Connecting the power cordDigital connection Digital output terminalSelecting the analog or digital input mode Turn on the powerTo turn off the power into standby Basic operationsAdjust the volume Selecting the digital decode modeListening with headphones Press TV Direct Adjusting the subwoofer audio positionActivating TV Direct AUDIO/TV/VCR/DBSSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Turning off the sounds temporarilyBasic settings From the remote control onlyTake your position where you listen to Sound Basic setting items Operating procedure Setting the speakersSetting subwoofer information-SUBWOOFER Setting subwoofer output-SUBWFR OUT Setting bass soundSetting the speaker distance Setting the crossover frequency-CROSS OverUsing the Midnight mode Selecting the main or sub channelVCR S/C Auto SR onAuto Sroff VCR CompntPress Adjust Sound adjustmentsBasic adjustment items Turn Multi JOG to adjust the selected itemAdjusting speaker output level Adjusting the effect level for DSP modes-EFFECTAdjusting the center tone-CENTER Tone Selecting the subwoofer sound phase-SBWFR Adjusting the bass soundsAttenuating the input signal-INPUT ATT Reinforcing the bass-BASS BoostTo store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsFrom the remote control Press FM/AM to select the band Selecting the FM reception modeTo tune in a preset station Press Tuner PresetIntroducing the Surround modes Creating realistic sound fieldsReproducing theater ambience Dolby Digital3D Headphone mode About other digital signalsDTS All Channel Stereo mode ALL CH ST Introducing the DSP modesDigital Acoustic Processor DAP modes Using the Surround/DSP modes Virtual Surround BackSelect and play any source other than DVD Multi Turn Multi JOG to select the Surround/DSP mode you wantTo cancel Surround/DSP modes Press SurroundConnections 2 Video cable connection AV Compu Link remote control systemConnections 1 AV Compu Link connection CaseAutomatic power on/off Connecting procedureAutomatic selection of TV’s input mode One-touch video playChannel + Operating other JVC productsVCR REC PauseTOP MENU/MENU DVD recorder or DVD playerDVR/DVD ZoomRelease TV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Try to operate your TV by pressing TVTry to operate your VCR by pressing VCR Changing the transmittable signals for operating a VCRRelease VCR Manufacturers’ codes for VCRManufacturers’ codes for DBS tuner Release DBSManufacturers’ codes for Catv converter Release DVR/DVDTroubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM tunerLimited Warranty Authorized Service Centers RX-F10S Home Theater Receiver Recepteur Pour Cinema Maison Mises en garde, précautions et indications diverses English Parts identification Front panel Getting started Connecting the FM and AM antennas Connecting the speakers Connecting video components Green Blue Red White Red DBS tuner Composite video cable not supplied You can connect any digital componens which have an optical Basic operations Adjust the volume Adjusting the subwoofer audio PositionTurning off the sounds temporarily Basic settings Basic setting items 12 cm Setting the crossover frequency-CROSS Over Dual Mono Setting Auto Surround-AUTO Surrnd Sound adjustments Adjusting the sound parameters for Adjusting the effect level for DSP modes-EFFECTSurround/DSP modes Adjusting the bass sounds From the remote control only Press the numeric buttons 1 10, +10 to Pro Logic II Movie Plii Movie and Pro Logic II Music Plii Plii MoviePlii Music English Introducing the DSP modes EX/ES setting SML/LRG AUTO/ONActivating the Surround/DSP modes AV Compu Link remote control system Connecting procedure Operating other JVC products DVD/CARD CancelReturn DimmerOperating other Manufacturers’Products English Release DBS Troubleshooting Power Requirements AC 120 V , 60 Hz Power Consumption EN, FR Victor Company of JAPAN, Limited 0404MWMMDWJEIN

RX-F10S specifications

The JVC RX-F10S is an impressive home theater receiver that embodies a blend of power, versatility, and advanced technology. Designed to enhance the audio-visual experience, this receiver offers a suite of features that cater to both casual listeners and audiophiles alike.

At the heart of the RX-F10S is its robust amplification system, delivering a powerful output that ensures high-quality sound reproduction across a wide range of frequencies. With multiple channels for surround sound support, it allows users to create an immersive audio environment, perfect for movie-watching or music enjoyment. The receiver supports various surround sound formats, such as Dolby Digital and DTS, enabling a cinematic experience right in the comfort of one's living room.

One of the standout features of the RX-F10S is its connectivity options. It is equipped with multiple HDMI inputs that support the latest 4K Ultra HD and HDR pass-through. This ensures compatibility with the latest gaming consoles, Blu-ray players, and streaming devices, providing future-proofing for your entertainment setup. In addition to HDMI, the receiver also includes optical and coaxial digital inputs, along with several analog inputs, providing flexibility in connecting various audio sources.

The RX-F10S is designed with user convenience in mind. Its intuitive on-screen interface simplifies the setup process and allows users to easily navigate through settings and options. The inclusion of a remote control further enhances usability, making it easy to switch between audio sources and adjust sound settings without getting up.

Another notable aspect of the JVC RX-F10S is its compatibility with wireless technologies. It features built-in Bluetooth that allows for seamless streaming from smartphones, tablets, and other compatible devices. This adds an extra layer of convenience, enabling users to enjoy their favorite music without the hassle of physical connections.

In terms of sound customization, the RX-F10S includes an equalizer that allows listeners to adjust their audio preferences according to their taste or the acoustics of their room. This level of personalization is crucial for those who seek a tailored listening experience.

Overall, the JVC RX-F10S is a versatile home theater receiver that combines powerful performance with a wide array of connectivity options and advanced features. Its ability to deliver high-quality sound while being user-friendly makes it an excellent choice for anyone looking to upgrade their home entertainment setup. Whether you are watching movies, playing games, or listening to music, the RX-F10S is poised to elevate your audio experience to new heights.