JVC RX-F10S manual Adjusting the bass sounds

English

Sound adjustments

Adjusting the sound localization of the center channel—CENTER GAIN

This setting is available only when Neo:6 Music is in use.

•If you have set “CENTER SPK” to “NO” (see page 18), the center gain is not adjustable.

•Once you have made an adjustment, it is memorized until you change the setting.

•You cannot use the remote control for this setting.

Adjustable range: 0 to 0.5 (in 0.1 step intervals)

Initial setting: C GAIN 0.2

As the number increases, the center channel will be localized clearly.

Normally, select “0.2.”

Adjusting the bass sounds

Reinforcing the bass—BASS BOOST

You can boost the bass level—Bass Boost.

•Once you have made an adjustment, it is memorized for each source.

B.BOOST ON Select to boost the bass level.

The BASS indicator lights up on the display.

B.BOOST OFF Select to deactivate the Bass Boost.

Initial setting: B.BOOST OFF

NOTE

This function affects only the sound coming out through the front speakers.

From the remote control:

Set the mode selector to “AUDIO/TV/VCR/DBS.”

Press SOUND, then press BASS

BOOST repeatedly.

•Each time you press BASS BOOST, the Bass Boost turns on and off alternately.

NOTE

After pressing SOUND, the numeric buttons work for sound adjustments. To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation; otherwise, the remote control may not work as you intend.

Attenuating the input signal—INPUT ATT

When the input level of analog source is too high, the sound will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion.

•Once you have made an adjustment, it is memorized for each source.

•You cannot use the remote control for this setting.

ATT ON	Select to attenuate the input signal level.
	The ATT indicator lights up on the display.
ATT NORMAL	Select to deactivate attenuation.

Initial setting: ATT NORMAL

Selecting the subwoofer sound phase—SBWFR

PHASE

You can change the subwoofer sound phase to your preference.

•Once you have made an adjustment, it is memorized for each source.

•You cannot use the remote control for this setting.

PHASE NORM. Normally select this.

PHASE REV. Select this when you feel the bass sound is better with this mode rather than with “PHASE NORM.”

Initial setting: PHASE NORM.

NOTE

This function takes effect only when “SUBWOOFER” is set to “SUBWFR :YES” (see page 18).

Adjusting the equalization patterns— D EQ 63Hz/250Hz/1kHz/4kHz/16kHz

You can adjust equalization patterns in five frequency bands (center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the front speakers.

•Once you have made an adjustment, it is memorized for each source.

Adjustable range: –8 (dB) to +8 (dB) (in 2 dB intervals)

Initial setting: 0 (dB) for all bands

•When adjustment is made, the EQ indicator lights up on the display.

If no adjustment is required, set all the frequency bands to

“0 (dB).”

• The EQ indicator goes off from the display.

From the remote control:

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

Set the mode selector to “AUDIO/TV/VCR/DBS.”

1Press SOUND.

2 Press EQ FREQ repeatedly to select the band you want to adjust.

3 Press EQ LEVEL +/– to adjust the equalization pattern of the selected band.

4 Repeat steps 2 and 3 to adjust	2
other bands.
	3
NOTE
After pressing SOUND, the numeric	1
buttons work for sound adjustments. To
use the numeric buttons to operate your
target source, press the corresponding
source selecting button before operation;
otherwise, the remote control may not
work as you intend.

24