ProForm PFEL59107.0 user manual Repeat this step for the right Pedal

Page 10

11.

Orient a Link Arm (30) as shown. Attach the

11

 

 

 

 

Left Pedal (34) to the Link Arm with three

 

 

 

 

 

 

 

 

 

M8 x 45mm Button Screws (90), three M8 Split

 

 

34

 

 

Washers (97), and three M8 x 23mm x 2mm

 

 

 

 

 

Washers (96).

 

 

 

 

 

Attach a Pedal Arm Cover (39) to the Link

 

 

80

 

 

 

 

 

39

 

Arm (30) with an M4 x 16mm Round Head

 

 

 

 

 

96

 

 

 

Screw (80).

 

 

 

 

 

 

 

 

 

Repeat this step for the Right Pedal (not

 

97

 

 

 

 

 

96

30

 

shown) and the other Link Arm (not shown).

 

 

 

 

 

97

 

 

 

 

 

 

 

 

 

 

90

 

12.

Apply a generous amount of grease to the axle

12

 

 

 

 

on the Left Upper Body Leg (24) and to the axle

 

 

 

 

 

24

 

 

 

on the left Crank Arm (55). Then, apply grease

 

 

 

 

to two Large Wave Washers (102).

 

Grease

32

 

 

 

 

 

Slide an Upper Body Leg Spacer (9) and a

 

 

 

 

 

Large Wave Washer (102) onto the Left Upper

 

102

9

 

 

Body Leg (24). Make sure that the flat side of

 

31

 

 

 

the Upper Body Leg Spacer is facing out-

 

 

 

 

 

 

 

 

 

ward. Then, slide the other Large Wave Washer

66

 

 

 

(102) onto the left Crank Arm (55).

 

 

 

 

 

Slide the left Pedal Arm (32) onto the Left Upper

86

95

 

 

 

 

32

 

 

Body Leg (24) while sliding the left Link Arm

 

 

 

 

 

 

 

 

(30) onto the axle on the left Crank Arm (55).

 

 

 

 

 

Attach the Pedal Arm (32) to the Left Upper

 

 

 

30

 

Body Leg (24) with an M8 x 23mm Button

 

 

 

 

 

 

 

 

 

Screw (86), an M8 Washer (95), an Axle Cover

 

 

 

 

 

(66), and an M8 x 23mm x 1mm Washer (31).

 

 

 

 

 

Then, attach the Link Arm (30) to the Crank Arm

 

 

 

 

 

(55) with an M8 x 23mm Button Screw (86), an

 

 

 

 

 

M8 Washer (95), a Large Axle Cover (52), and

 

 

 

 

 

an M8 x 23mm x 1mm Washer (31).

 

 

 

 

 

Repeat this step for the right Pedal

 

30

102

 

 

 

 

 

 

 

 

 

 

 

Arm (32) and the right Link Arm (30).

 

 

31

 

 

 

 

95

55

 

 

See step 4. Tighten the M8 x 19mm Button

 

 

 

 

 

 

Grease

 

 

Screws (85).

 

 

 

 

 

 

52

 

 

 

 

86

 

 

 

 

 

 

13.Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical exerciser.

10

Image 10
Contents Model No. PFEL59107.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Rear Before YOU BeginFront Right SideAssembly Page Avoid pinching the Wire Harnesses 64, 65 during this step Avoid pinching Wire Harnesses 64 During this stepRepeat this step for the Right Upper Body Leg Attach the Right Upper Body Arm 23 in the same wayRight Front Upper Body Cover Avoid pinching Wire harnesses during this stepAttach the Right Rear Upper Body Cover Same wayRepeat this step for the right Pedal HOW to Fold and Unfold the Elliptical Exerciser HOW to USE the Elliptical ExerciserHOW to Move the Elliptical Exerciser HOW to Exercise on the Elliptical Exerciser Features of the Console HOW to USE the Manual Mode Select one of the six cross training programs HOW to USE a Cross Training ProgramTurn on the fan if desired Begin pedaling to start the programChase dumbbells or an exercise ball, call Als will automatically adjust to the resistancePerform the first strength exercise when Prompted Toll-free telephone number on the front coverFollow your progress with the display HOW to USE a Heart Rate ProgramSelect one of the two heart rate programs Follow your progress with the display Handgrip Pulse Sensor Troubleshooting Maintenance and TroubleshootingBattery Replacement HOW to Adjust the BeltWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Page Page Part LIST-Model No. PFEL59107.0 Key No. Qty DescriptionQty Description Drawing A-Model No Drawing Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT