JVC LVT1007-005A manual Operating JVC’s Audio/Video Components, Operating Audio Components, Tuner

Page 45

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC’s components are preset in the remote control.

English

Operating Audio Components

IMPORTANT:

To operate JVC’s audio components using the supplied remote control:

You need to connect JVC’s audio components through the COMPU LINK (SYNCHRO) jacks (see page 39) in addition to the connections using cables with RCA pin plugs (see page 10).

Aim the remote control directly at the remote sensor on the receiver.

If you use the buttons on the front panel to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using source selection buttons on the remote control.

To operate the target component using the COMPU LINK remote control system, set the source name correctly if required. (See page 19.)

Refer also to the manuals supplied with your components.

Tuner

You can always perform the following operations:

FM/AM: Alternate between FM and AM.

After pressing FM/AM, you can perform the following operations on a tuner:

1 – 10/0, +10: Select a preset channel number directly. For channel number 5, press 5.

For channel number 15, press +10, then 5. For channel number 20, press +10, then 10/0.

TUNING UP/DOWN:

Tune into stations.

FM MODE: Change the FM reception mode.

Sound control section (Amplifier)

You can always perform the following operations:

SURROUND: Turn on and select Surround modes

DSP:Turn on and select DSP modes.

SURR/DSP OFF: Turn off Surround and DSP modes.

After pressing SOUND, you can perform the following operations:

FRONT•L then LEVEL +/–:Adjust the left front speaker output level.

FRONT•R then LEVEL +/–:Adjust the right front speaker output

level.

CENTER then LEVEL +/–: Adjust the center speaker output level.

SURR•L then LEVEL +/–: Adjust the left surround speaker output level.

SURR•R then LEVEL +/–: Adjust the right surround speaker output level.

SURR BACK then LEVEL +/–:

Adjust the surround back speaker output level.

SUBWOOFER then LEVEL +/–:

Adjust the subwoofer output level.

DIGITAL EQ then LEVEL+/–: Select the sound frequency bands

 

and adjust its level.

TEST:

Turn on or off test tone output.

BASS BOOST:

Turn on or off Bass Boost.

Note:

After adjusting sounds, press the corresponding source selection button to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.

CD player

After pressing CD, you can perform the following operations on a CD player:

3: Start playing.

4: Return to the beginning of the current (or previous) track.

¢: Skip to the beginning of the next track.

7: Stop playing.

8: Pause playing. To resume, press 3.

1 – 10/0, +10:

Select a track number directly. For track number 5, press 5.

For track number 15, press +10, then 5. For track number 20, press +10, then 10/0.

For track number 30, press +10, +10, then 10/0.

42

Image 45
Contents RX-7032VSL Precaução -- Interruptor STANDBY/ON Precaución -- Interruptor STANDBY/ONPrecaución Ventilación Adecuada Features PrecautionsIntroduction Table of Contents Remote Control Parts IdentificationButtons 15, 44 Front Panel Display WindowInside the front door Press down on PUSH-OPEN How to open the front doorOutput Rear PanelChecking the Supplied Accessories Before InstallationAdjusting the Voltage Selector Putting Batteries in the Remote ControlAM Antenna Connections Connecting the FM and AM AntennasFM Antenna Connections Outdoor FM Antenna CableInsert the speaker signal cable Connecting the SpeakersBasic connecting procedure Close the speaker terminalPlacing speakers Connecting the subwoofer speakerFront speakers and center speaker Surround and surround back speakersAnalog Connections Connecting Audio/Video ComponentsCassette deck CD playerIf your video components have an AV Compulink jack Video component connectionsTV and/or DBS tuner To listen to the sound after connection, press VCRDVD player DVD playerTo listen to the sound after connection, press DVD Multi Plug the power cord into an AC outlet Connecting the Power CordDigital Connections Digital output terminalDaily Operational Procedure Selecting the Source to Play Turning On the PowerBasic Operations Speaker and signal indicators on the display Adjusting the VolumeWhen analog input is selected Always lights up Selecting different sources for picture and soundListening with headphones only Selecting the Analog or Digital Input ModeSubwoofer Sound To use the speakers connected to the Front SpeakersTo select the analog input mode again Setting the Dynamic RangeTurning Analog Direct On and Off Reinforcing the Bass Using the Sleep TimerMuting the Sound Changing the Display BrightnessTuning in to Stations Manually Using Preset TuningReceiving Radio Broadcasts While listening to an FM station, press FM Mode Selecting the FM Reception ModePress the 10 keys to select a preset channel number To tune in a preset stationSetting the Speakers Configuration Remote Basic SettingsPress Quick Speaker Setup Press in Multi JOG Push SETSpeakers channels number and size Basic Setting ItemsRoom size and speaker distance Items To do SeePress Setting Basic ProcedureSetting the Speakers Push in Multi JOG Push SETSurround back speakers quantity-SBACK OUT Setting the Speaker Distance2SPK Select this to use 2 surround back speakers Measuring unit-DIST UnitSelecting main or sub channel-DUAL Mono Setting the Bass SoundsSelect one of the following Select the playback sounds channelSetting the Component Video Input Setting the Digital Input TerminalsMemorizing the Volume Level for Each Source To recall the volume levelBasic Setting Items Basic Procedure Adjusting SoundPress Adjust Ex. When adjusting the subwoofer level toAdjusting the Speaker Output Levels Adjusting the Equalization PatternsEqualization adjustment-DIGITAL EQ Repeat steps 2 and 3 to adjust the other center frequencyAdjustable parameters Select a speaker you want to adjustFor DAP modes For Pro Logic II Music onlyReproducing Theater Ambience Introducing the Surround Modes Using the Surround ModesDTS Digital Surround What is Dual Mono?DTS Extended Surround DTS-ES DTS 96/24EX/ES Setting Available Surround Mode Incoming Signal TypeSurround Modes Applicable to the Various Software 3D Headphone Mode-3D H PhonePress Surround to activate the Surround mode Activating the Surround ModesSelect and play any source other than DVD Multi 3D Headphone Mode Using the DSP ModesReproducing the Sound Field Introducing the DSP ModesALL Channel Stereo mode To cancel the DSP modesMulti-channel digital signals Activating the DSP ModesActivating the DVD Multi Playback Mode Using the DVD Multi Playback ModeConnection diagram Press DVD Multi so that DVD Multi appears on the displayRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemPress the play 3 button on the CD player Automatic Source SelectionConnections 1 AV Compu Link Connection AV Compu Link Remote Control SystemConnections 2 Video Cable Connection Video cord To Video InputAutomatic Power On/Off Automatic Selection of TV’s Input ModeOne-Touch Video Play One-Touch DVD PlayOperating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section Amplifier7/P CD changerCD recorder Cassette deckOperating Video Components DVD playerCH + Release TV If there are more than one code listed for your brand of TVTry to operate your TV by pressing TV For TV Manufacturer CodesFor DBS tuner Release CATV/DBSFor Catv converter Manufacturer CodesRelease VCR If there are more than one code listed for your brandTry to operate your VCR by pressing VCR For VCRFor DVD player Release AudioDenon Panasonic Philips Pioneer 04, 05 Samsung Sony Toshiba YamahaProblem Possible Cause Solution TroubleshootingSpecifications AudioVideo Precaução para a ligação à tensão da rede CA Precaución para la línea de la red CA