JVC RX-5001VGD manual Basic Settings, Changing the Source Name

Page 14

English

Basic Settings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD jacks on the rear panel: Change the source name shown on the display when you select the MD recorder as the source.

On the front panel ONLY:

When changing the source name from “TAPE” to “M D”:

MULTI CURSOR

3.Press MULTI CURSOR @/ #to select your center speaker size.

LARGE SMALL NO

LARGE: Select this mode when the size of the center speaker is the same as that of the front speakers.

1.Press TAPE/MD.

• Make sure “TAPE” appears on the display.

2.Press and hold SOURCE NAME (the same button as TAPE/MD) until “M D” appears on the display.

TAPE/MD

SOURCE NAME

TAPE/MD

SOURCE NAME

SMALL: Select this mode when the size of the center speaker

is smaller than that of the front speakers.

NO: Select this mode when you do not use a center speaker.

Rear Speaker Setting

Register whether you have connected the rear speakers or not.

To change the source name from “M D” to “TAPE,”

repeat the same procedure above (in step 1, make sure “M D” appears on the display).

Note:

Without changing the source name, you can still use the connected components. However, there may be some inconvenience.

“TAPE” will appear on the display when you select the MD recorder.

You cannot use the COMPU LINK remote control system (see page 21) to operate the MD recorder.

Setting Center and Rear Speakers for

the DSP Modes

To obtain the best possible surround sound of the DSP (Digital Signal Processor) modes (see page 15), you have to register the information about the speaker arrangement after all connections are completed.

Center Speaker Setting

Register the center speaker size.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1.

Press SETTING so that MULTI

SETTING

 

CURSOR %/ Þbuttons work for

 

 

setting the center speaker size.

 

2.

Press MULTI CURSOR %/ Þ

MULTI CURSOR

 

repeatedly until “CNTR SPK”

 

 

(Center Speaker) appears on the

 

 

display.

 

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1.

Press SETTING so that MULTI

SETTING

 

 

CURSOR %/ Þbuttons work for

 

 

setting the rear speaker

 

 

information.

 

2.

Press MULTI CURSOR %/ Þ

MULTI CURSOR

 

repeatedly until “REAR SPK”

 

 

(Rear Speaker) appears on the

 

 

display.

 

3.

Press MULTI CURSOR @/ #to

MULTI CURSOR

register whether you have connected the rear speakers.

YES: Select this mode when you use rear speakers.

NO: Select this mode when you do not use rear speakers.

Note:

When you change your speakers, you need to register the information about the speakers again.

Delay Time Setting

Register the delay time of the sound from the rear speakers, comparing the sound from the front speakers.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

You can adjust the delay time only when you have connected the rear speakers and have set “REAR SPK” to “YES’’ (see above).

Delay time setting is only valid for “PROLOGIC” (see page 15).

11

Image 14
Contents RX-5000VBK / RX-5001VGD Precaución English Español Português Table of Contents Front Panel Remote ControlParts Identification To use the Cursor control buttons q on the front panelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedConnecting the front speakers Connecting the SpeakersAM Antenna ConnectionsBasic connecting procedure Connecting the rear and center speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker If your audio components have a Compu LINK-3 terminalVideo component connections Plug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Replace the coverSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Selecting the Front Speakers Adjusting the VolumeMuting the Sound Recording a SourceAdjusting the Tone Attenuating the Input SignalAdjusting the Front Speaker Output Balance Reinforcing the BassChanging the Source Name Basic SettingsSetting Center and Rear Speakers for DSP Modes Storing the Basic Settings Adjustments One Touch Operation Using the Sleep TimerTuning in Stations Manually Setting the AM Tuner Interval SpacingUsing Preset Tuning Receiving Radio BroadcastsPress FM/AM Selecting the FM Reception ModePress Multi Cursor @/ #to select a preset channel station Press FMSurround Modes Using the DSP Modes3D-PHONIC modes Dolby SurroundRear Speaker Available DSP Modes According to the Speaker ArrangementFront RearAdjusting the 3D-PHONIC Modes Adjusting the DAP ModesOutput balance Press Rearl / + to adjustPress Test to check the speaker Rear speaker output levelSelect and play a sound source Repeatedly until -CENTER+ Appears on the displayActivating the DSP Modes Only for JVC TheaterPress DVD Multi Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Repeatedly until -REAR L+Same time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionCassette deck Operating JVC’s Audio/Video ComponentsSound control section Amplifier TunerMD recorder CD player-changer7/P DVD playerTroubleshooting Problem Possible Cause SolutionAudio SpecificationsAmplifier VideoGeneral FM tuner IHFAM tuner Precaução para a ligação à tensão da rede CA Precaución para la línea de la red CA