JVC RX-5001VGD manual FM tuner IHF, AM tuner, General

Page 29

FM tuner (IHF)
Tuning Range:	87.50 MHz to 108.00 MHz
Usable Sensitivity:	Monaural: 12.8 dBf (1.20 µV/75 Ω)
50 dB Quieting Sensitivity:
Monaural:	21.3 dBf (3.2 µV/75	Ω)
Stereo:	41.3 dBf (31.5 µV/75	Ω)
Signal-to-Noise Ratio (IHF-A weighted):
Monaural:	78 dB at 85 dBf
Stereo:	73 dB at 85 dBf
Total Harmonic Distortion:
Monaural:	0.4% at 1 kHz
Stereo:	0.6% at 1 kHz

Stereo Separation at REC OUT: 35 dB at 1 kHz

Alternate Channel Selectivity:

45 dB: (±400 kHz)

Frequency Response: 30 Hz to 15 kHz: (+0.5 dB, –3 dB)

AM tuner
Tuning Range:	531 kHz to 1,602 kHz (at 9 kHz interval)
	530 kHz to 1,600 kHz (at 10 kHz interval)
Usable Sensitivity:	Loop antenna 400 µV/m

Signal-to-Noise Ratio: 50 dB (100 mV/m)

General
Power Requirements:	AC 220 V ,
	adjustable with the voltage selector,
	50 Hz
Power Consumption:	250 W (at operation)
	5 W (in standby mode)
Dimensions (W x H x D):	435 mm x 146 mm x 403.5 mm
	(17 3/16 in. x 5 3/4 in. x 15 15/16 in.)
Mass:	10.2 kg (22.5 lbs)

Designs & specifications are subject to change without notice.

English

26

Image 29

Contents RX-5000VBK / RX-5001VGD Precaución English Español Português Table of Contents Parts Identification Remote ControlFront Panel To use the Cursor control buttons q on the front panelConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Getting StartedAM Antenna ConnectionsBasic connecting procedure Connecting the SpeakersConnecting the front speakers Connecting the rear and center speakersConnecting the subwoofer speaker Connecting Audio/Video ComponentsAudio component connections If your audio components have a Compu LINK-3 terminalVideo component connections Putting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Replace the coverSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Muting the Sound Adjusting the VolumeSelecting the Front Speakers Recording a SourceAdjusting the Front Speaker Output Balance Attenuating the Input SignalAdjusting the Tone Reinforcing the BassChanging the Source Name Basic SettingsSetting Center and Rear Speakers for DSP Modes Using the Sleep Timer Storing the Basic Settings Adjustments One Touch OperationUsing Preset Tuning Setting the AM Tuner Interval SpacingTuning in Stations Manually Receiving Radio BroadcastsPress Multi Cursor @/ #to select a preset channel station Selecting the FM Reception ModePress FM/AM Press FM3D-PHONIC modes Using the DSP ModesSurround Modes Dolby SurroundFront Available DSP Modes According to the Speaker ArrangementRear Speaker RearAdjusting the DAP Modes Adjusting the 3D-PHONIC ModesPress Test to check the speaker Press Rearl / + to adjustOutput balance Rear speaker output levelActivating the DSP Modes Repeatedly until -CENTER+ Appears on the displaySelect and play a sound source Only for JVC TheaterActivating the DVD Multi Playback Mode Using the DVD Multi Playback ModePress DVD Multi Repeatedly until -REAR L+Remote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemSame time Automatic Source SelectionSound control section Amplifier Operating JVC’s Audio/Video ComponentsCassette deck Tuner7/P CD player-changerMD recorder DVD playerProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsAudio VideoGeneral FM tuner IHFAM tuner Precaución para la línea de la red CA Precaução para a ligação à tensão da rede CA