JVC RX-5001VGD manual Using the DVD Multi Playback Mode, Activating the DVD Multi Playback Mode

Page 23

Using the DVD MULTI Playback Mode

This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD player. Before playing back a DVD, refer also to the manual supplied with the DVD player.

English

Activating the DVD MULTI Playback Mode

You can adjust the DVD MULTI playback mode while playing back a DVD using the analog discrete output mode on the DVD player. Once you made adjustments, the receiver memorizes the

MULTI CURSOR

7.Press MULTI CURSOR @/ #to adjust the left rear speaker output level (from –10 to +10).

adjustments until you change them.

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 11).

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•You can only adjust the rear and/or center speaker output levels when you have connected rear speakers and/or a center speaker and have set “REAR SPK” and/or “CNTR SPK” correctly. See page 11.

8.Press MULTI CURSOR %/ Þ repeatedly until “–REAR R+” appears on the display.

9.Press MULTI CURSOR @/ #to adjust the right rear speaker output level (from –10 to +10).

MULTI CURSOR

MULTI CURSOR

On the front panel:

DVD MULTI

1. Press DVD MULTI .

Note:

When you select “DVDMULTI” as the source to play, the DSP mode is canceled temporarily, and the SURROUND button does not work.

From the remote control:

1. Press DVD MULTI.

DVD MULTI

 

Note:

When you select “DVDMULTI” as the source to play, the DSP mode is canceled temporarily, and the SURROUND button does not work.

2.Select the analog discrete output mode on the DVD player, and start playing a DVD.

• Refer to the manual supplied with the DVD player.

If you need to make any adjustment, go to the following steps.

3. Press ADJUST so that MULTI

ADJUST

CURSOR %/ Þ/ @/ #buttons

 

work for adjusting the DVD

 

MULTI playback setting.

 

2.Select the analog discrete output mode on the DVD player, and start playing a DVD.

• Refer to the manual supplied with the DVD player.

If you need to make any adjustment, go to the following steps.

3. Press SOUND CONTROL.

SOUND

CONTROL

The 10 keys are activated for adjusting the sound.

4. Press CENTER – / + to adjust the – CENTER +

5

5

6

4. Press MULTI CURSOR %/ Þ

repeatedly until “–CENTER+”

appears on the display.

MULTI CURSOR

center speaker output level.

•Pressing CENTER – decreases the output level up to –10 dB.

•Pressing CENTER + increases the output level up to +10 dB.

5.

Press MULTI CURSOR @/ #to

 

adjust the center speaker output

 

level (from –10 to +10).

6.

Press MULTI CURSOR %/ Þ

 

repeatedly until “–REAR L+”

 

appears on the display.

MULTI CURSOR

MULTI CURSOR

5.Press REAR•L – / + to adjust the left rear speaker output level.

•Pressing REAR•L – decreases the output level up to –10 dB.

•Pressing REAR•L + increases the output level up to +10 dB.

6.Press REAR•R – / + to adjust the right rear speaker output level.

•Pressing REAR•R – decreases the output level up to –10 dB.

•Pressing REAR•R + increases the output level up to +10 dB.

– REAR•L +

85 9

– REAR•R +

10 +10

20

Page 22 Page 24
Image 23
Page 22 Page 24
Contents RX-5000VBK / RX-5001VGD Precaución English Español Português Table of Contents To use the Cursor control buttons q on the front panel Remote ControlParts Identification Front PanelGetting Started Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesConnecting the rear and center speakers Connecting the SpeakersAM Antenna ConnectionsBasic connecting procedure Connecting the front speakersIf your audio components have a Compu LINK-3 terminal Connecting Audio/Video ComponentsConnecting the subwoofer speaker Audio component connectionsVideo component connections Replace the cover Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Recording a Source Adjusting the VolumeMuting the Sound Selecting the Front SpeakersReinforcing the Bass Attenuating the Input SignalAdjusting the Front Speaker Output Balance Adjusting the ToneChanging the Source Name Basic SettingsSetting Center and Rear Speakers for DSP Modes Using the Sleep Timer Storing the Basic Settings Adjustments One Touch OperationReceiving Radio Broadcasts Setting the AM Tuner Interval SpacingUsing Preset Tuning Tuning in Stations ManuallyPress FM Selecting the FM Reception ModePress Multi Cursor @/ #to select a preset channel station Press FM/AMDolby Surround Using the DSP Modes3D-PHONIC modes Surround ModesRear Available DSP Modes According to the Speaker ArrangementFront Rear SpeakerAdjusting the DAP Modes Adjusting the 3D-PHONIC ModesRear speaker output level Press Rearl / + to adjustPress Test to check the speaker Output balanceOnly for JVC Theater Repeatedly until -CENTER+ Appears on the displayActivating the DSP Modes Select and play a sound sourceRepeatedly until -REAR L+ Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Press DVD MultiAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Same timeTuner Operating JVC’s Audio/Video ComponentsSound control section Amplifier Cassette deckDVD player CD player-changer7/P MD recorderProblem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier AudioGeneral FM tuner IHFAM tuner Precaución para la línea de la red CA Precaução para a ligação à tensão da rede CA
Top Page Image Contents