JVC RX-5001VGD manual Troubleshooting, Problem Possible Cause Solution

Page 27

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

 

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

 

 

 

The display does not light up.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

 

 

 

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring and reconnect if

 

 

 

 

necessary.

 

 

 

 

 

 

 

 

 

The SPEAKERS 1 and 2 buttons are not

Press SPEAKERS 1 and 2 correctly.

 

 

 

set correctly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

 

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute.

 

 

 

 

 

 

Sound from one speaker only.

Speaker signal cables are not connected

Check speaker wiring and reconnect if

 

 

 

properly.

necessary.

 

 

 

 

 

 

 

 

 

The balance is set to one extreme.

Adjust the balance properly (see page 9).

 

 

 

 

 

 

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outside FM antenna or contact

 

reception.

 

your dealer.

 

 

 

 

 

 

 

 

 

 

The station is too far away.

Select a new station.

 

 

 

 

 

 

 

 

 

An incorrect antenna is used.

Check with your dealer to be sure you have

 

 

 

 

the correct antenna.

 

 

 

 

 

 

 

 

 

 

Antennas are not connected properly.

Check connections.

 

 

 

 

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

 

reception.

 

traffic.

 

 

 

 

 

 

 

Howling during record playing.

Your turntable is too close to speakers.

Move speakers away from the turntable.

 

 

 

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of high

Rotate the MASTER VOLUME control

 

display.

volume.

counterclockwise three or four times, then

 

 

 

 

press STANDBY/ON

 

 

 

 

on the front panel.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If “OVERLOAD” does not disappear, unplug

 

 

 

 

the AC power cord, then plug it back again.

 

 

 

 

 

 

 

 

 

 

 

 

 

Speakers are overloaded because of short

Press STANDBY/ON

 

 

on the front panel,

 

 

 

 

 

 

 

 

 

 

 

circuit of speaker terminals.

then check the speaker wiring.

 

 

 

 

If “OVERLOAD” does not disappear, unplug

 

 

 

 

the AC power cord, then plug it back again.

 

 

 

 

If speaker wiring is not short-circuited,

 

 

 

 

contact your dealer.

 

 

 

 

 

 

 

 

 

 

 

 

Remote control does not work.

There is an obstruction in front of the

Remove the obstruction.

 

 

 

 

remote sensor on the receiver.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Batteries are weak.

Replace batteries.

 

 

 

 

 

 

 

 

 

 

 

English

24

Image 27
Contents RX-5000VBK / RX-5001VGD Precaución English Español Português Table of Contents To use the Cursor control buttons q on the front panel Remote ControlParts Identification Front PanelGetting Started Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesConnecting the rear and center speakers Connecting the SpeakersAM Antenna ConnectionsBasic connecting procedure Connecting the front speakersIf your audio components have a Compu LINK-3 terminal Connecting Audio/Video ComponentsConnecting the subwoofer speaker Audio component connectionsVideo component connections Replace the cover Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletTurning the Power On and Off Standby Basic OperationsSelecting the Source to Play Recording a Source Adjusting the VolumeMuting the Sound Selecting the Front SpeakersReinforcing the Bass Attenuating the Input SignalAdjusting the Front Speaker Output Balance Adjusting the ToneBasic Settings Setting Center and Rear Speakers for DSP ModesChanging the Source Name Using the Sleep Timer Storing the Basic Settings Adjustments One Touch OperationReceiving Radio Broadcasts Setting the AM Tuner Interval SpacingUsing Preset Tuning Tuning in Stations ManuallyPress FM Selecting the FM Reception ModePress Multi Cursor @/ #to select a preset channel station Press FM/AMDolby Surround Using the DSP Modes3D-PHONIC modes Surround ModesRear Available DSP Modes According to the Speaker ArrangementFront Rear SpeakerAdjusting the DAP Modes Adjusting the 3D-PHONIC ModesRear speaker output level Press Rearl / + to adjustPress Test to check the speaker Output balanceOnly for JVC Theater Repeatedly until -CENTER+ Appears on the displayActivating the DSP Modes Select and play a sound sourceRepeatedly until -REAR L+ Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Press DVD MultiAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Same timeTuner Operating JVC’s Audio/Video ComponentsSound control section Amplifier Cassette deckDVD player CD player-changer7/P MD recorderProblem Possible Cause Solution TroubleshootingVideo SpecificationsAmplifier AudioFM tuner IHF AM tunerGeneral Precaución para la línea de la red CA Precaução para a ligação à tensão da rede CA