JVC RX-5001VGD manual Table of Contents

Page 4

English

Table of Contents
Parts Identification	2
Getting Started	3
Before Installation	3
Checking the Supplied Accessories	3
Connecting the FM and AM Antennas	3
Connecting the Speakers	4
Connecting Audio/Video Components	5
Connecting the Power Cord	7
Putting Batteries in the Remote Control	7
Basic Operations	8
Turning the Power On and Off (Standby)	8
Selecting the Source to Play	8
Adjusting the Volume	9
Selecting the Front Speakers	9
Muting the Sound	9
Recording a Source	9
Attenuating the Input Signal	10
Adjusting the Front Speaker Output Balance	10
Reinforcing the Bass	10
Adjusting the Tone	10
Basic Settings	11
Changing the Source Name	11
Setting Center and Rear Speakers for the DSP Modes	11
Storing the Basic Settings and Adjustments — One Touch
Operation	12
Using the Sleep Timer	12
Receiving Radio Broadcasts	13
Setting the AM Tuner Internal Spacing	13
Tuning in Stations Manually	13
Using Preset Tuning	13
Selecting the FM Reception Mode	14
Using the DSP Modes	15
Available DSP Modes According to the Speaker Arrangement ..	16
Adjusting the 3D-PHONIC Modes	17
Adjusting the DAP Modes	17
Adjusting the Surround Modes — Dolby Surround and JVC
Theater Surround	18
Activating the DSP Modes	19
Using the DVD MULTI Playback Mode	20
Activating the DVD MULTI Playback Mode	20
COMPU LINK Remote Control System	21
Operating JVC’s Audio/Video Components ...	22
Troubleshooting	24
Specifications	25

1

Image 4

Contents RX-5000VBK / RX-5001VGD Precaución English Español Português Table of Contents Remote Control Parts IdentificationFront Panel To use the Cursor control buttons q on the front panelBefore Installation Connecting the FM and AM AntennasChecking the Supplied Accessories Getting StartedConnecting the Speakers AM Antenna ConnectionsBasic connecting procedureConnecting the front speakers Connecting the rear and center speakersConnecting Audio/Video Components Connecting the subwoofer speakerAudio component connections If your audio components have a Compu LINK-3 terminalVideo component connections Connecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Replace the coverBasic Operations Turning the Power On and Off StandbySelecting the Source to Play Adjusting the Volume Muting the SoundSelecting the Front Speakers Recording a SourceAttenuating the Input Signal Adjusting the Front Speaker Output BalanceAdjusting the Tone Reinforcing the BassSetting Center and Rear Speakers for DSP Modes Basic SettingsChanging the Source Name Storing the Basic Settings Adjustments One Touch Operation Using the Sleep TimerSetting the AM Tuner Interval Spacing Using Preset TuningTuning in Stations Manually Receiving Radio BroadcastsSelecting the FM Reception Mode Press Multi Cursor @/ #to select a preset channel stationPress FM/AM Press FMUsing the DSP Modes 3D-PHONIC modesSurround Modes Dolby SurroundAvailable DSP Modes According to the Speaker Arrangement FrontRear Speaker RearAdjusting the 3D-PHONIC Modes Adjusting the DAP ModesPress Rearl / + to adjust Press Test to check the speakerOutput balance Rear speaker output levelRepeatedly until -CENTER+ Appears on the display Activating the DSP ModesSelect and play a sound source Only for JVC TheaterUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModePress DVD Multi Repeatedly until -REAR L+Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverSame time Automatic Source SelectionOperating JVC’s Audio/Video Components Sound control section AmplifierCassette deck TunerCD player-changer 7/PMD recorder DVD playerTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierAudio VideoAM tuner FM tuner IHFGeneral Precaução para a ligação à tensão da rede CA Precaución para la línea de la red CA