JVC RX-5001VGD manual Adjusting the 3D-PHONIC Modes, Adjusting the DAP Modes

Page 20

English

Adjusting the 3D-PHONIC Modes

Before you start, remember...

Make sure that you have set the speaker information correctly (see page 11).

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Adjusting the DAP Modes

Before you start, remember...

Make sure that you have set the speaker information correctly

(see page 11).

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

• You can only adjust the rear speaker output level when you have

On the front panel:

1. Press SURROUND repeatedly until “3DACTION” or “3DTHEATR” appears on the display.

SURROUND

connected the rear speakers and have set “REAR SPK” to “YES”

(see page 11).

On the front panel:

1. Press SURROUND repeatedly

The 3D-PHONIC and PRO LOGIC indicators also light up on the display.

SURROUND

until the DAP mode — DANCE

CLUB, LIVE CLUB, HALL, or

2.Press ADJUST so that MULTI CURSOR %/ Þ/ @/ #buttons work for adjusting the surround setting.

3.Press MULTI CURSOR %/ Þ repeatedly until “–EFFECT+” appears on the display.

ADJUST

MULTI CURSOR

PAVILION — appears on the

 

display.

 

The DAP indicator also lights up on the display.

 

2. Press ADJUST so that MULTI

ADJUST

 

CURSOR %/ Þ/ @/ #buttons

 

work for adjusting the DSP

 

setting.

 

3. Press MULTI CURSOR %/ Þ

MULTI CURSOR

 

MULTI CURSOR

4.Press MULTI CURSOR @/ #to select an effect level you want.

Each time you press the button, the effect level changes as follows:

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5

EFFECT 4

As the number increases, the selected 3D-PHONIC mode becomes stronger.

repeatedly until “– REAR +”

 

appears on the display.

 

4. Press MULTI CURSOR @/ #to

MULTI CURSOR

 

adjust the rear speaker output

 

level (from –10 to +10).

 

Note:

From the remote control:

1. Press SOUND CONTROL.

SOUND

CONTROL

You cannot adjust the left and right rear speaker output levels

separately.

The 10 keys are activated for sound adjustments.

2.Press SURROUND repeatedly until “3DACTION” or “3DTHEATR” appears on the display.

SURROUND

3

5. Press MULTI CURSOR %/ Þ

repeatedly until “–EFFECT+”

appears on the display.

MULTI CURSOR

The 3D-PHONIC and PRO LOGIC indicators also light up on the display.

3. Press EFFECT to select an effect

EFFECT

level you want.

45

• Each time you press the button, the effect

 

level changes as follows:

 

6. Press MULTI CURSOR @/ #to

select an effect level you want.

• Each time you press the button, the effect

level changes as follows:

MULTI CURSOR

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5

EFFECT 4

As the number increases, the selected 3D-PHONIC mode becomes stronger.

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5

EFFECT 4

As the number increases, the selected DAP mode becomes stronger.

17

Image 20
Contents RX-5000VBK / RX-5001VGD Precaución English Español Português Table of Contents Remote Control Parts IdentificationFront Panel To use the Cursor control buttons q on the front panelBefore Installation Connecting the FM and AM AntennasChecking the Supplied Accessories Getting StartedConnecting the Speakers AM Antenna ConnectionsBasic connecting procedureConnecting the front speakers Connecting the rear and center speakersConnecting Audio/Video Components Connecting the subwoofer speakerAudio component connections If your audio components have a Compu LINK-3 terminalVideo component connections Connecting the Power Cord Putting Batteries in the Remote ControlPlug the power cord into an AC outlet Replace the coverSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Adjusting the Volume Muting the SoundSelecting the Front Speakers Recording a SourceAttenuating the Input Signal Adjusting the Front Speaker Output BalanceAdjusting the Tone Reinforcing the BassChanging the Source Name Basic SettingsSetting Center and Rear Speakers for DSP Modes Storing the Basic Settings Adjustments One Touch Operation Using the Sleep TimerSetting the AM Tuner Interval Spacing Using Preset TuningTuning in Stations Manually Receiving Radio BroadcastsSelecting the FM Reception Mode Press Multi Cursor @/ #to select a preset channel stationPress FM/AM Press FMUsing the DSP Modes 3D-PHONIC modesSurround Modes Dolby SurroundAvailable DSP Modes According to the Speaker Arrangement FrontRear Speaker RearAdjusting the 3D-PHONIC Modes Adjusting the DAP ModesPress Rearl / + to adjust Press Test to check the speakerOutput balance Rear speaker output levelRepeatedly until -CENTER+ Appears on the display Activating the DSP ModesSelect and play a sound source Only for JVC TheaterUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModePress DVD Multi Repeatedly until -REAR L+Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverSame time Automatic Source SelectionOperating JVC’s Audio/Video Components Sound control section AmplifierCassette deck TunerCD player-changer 7/PMD recorder DVD playerTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierAudio VideoGeneral FM tuner IHFAM tuner Precaução para a ligação à tensão da rede CA Precaución para la línea de la red CA