JVC RX-8012RSL CTR Delay Center Delay Appears on the display, Press Control UP 5/DOWN Control

Page 21

Center Delay Time Setting

Register the delay time of the sound from the center speaker, comparing to that of the sound from the front speakers.

If the distance from your listening point to the center speaker is equal to that to the front speakers, select 0 ms. As the distance to the center speaker becomes shorter, increase the delay time.

1 msec increase (or decrease) in delay time corresponds to 30 cm decrease (or increase) in distance.

When shipped from the factory, the delay time is set to 0 ms.

On the front panel ONLY:

1. Press SETTING repeatedly until

CT SETTING

“CTR DELAY” (Center Delay)

 

appears on the display.

 

The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN ° CONTROL

 

 

Center

 

 

 

Left front

speaker

Right front

speaker

 

 

 

 

speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.0 m

2.7 m

2.4 m

2.1 m

Left rear

Right rear

speaker

speaker

to select the delay time of the

DOWN UP

center speaker output (from 0 ms to 5 ms).

Notes:

Center delay time is not valid for the DVD MULTI playback mode.

You cannot adjust the center delay time when you have set “CTR SPK” to “NONE.”

Rear Delay Time Setting

Register the delay time of the sound from the rear speakers, comparing to that of the sound from the front speakers.

If the distance from your listening point to the rear speakers is equal to that to the front speakers, select 0 ms. As the distance to the rear speakers becomes shorter, increase the delay time.

1 msec increase (or decrease) in delay time corresponds to 30 cm decrease (or increase) in distance.

When shipped from the factory, the delay time is set to 5 ms.

Ex.: In this case, set the center delay time to “1 ms” and the rear delay time to “2 ms.”

Crossover Frequency Setting

Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocates the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker).

To use this function properly, you need to set the crossover frequency level according to the size of the small speaker connected.

If you have selected “LARGE” for all speakers (see page 17), this function cannot be adjusted.

On the front panel ONLY:

1. Press SETTING repeatedly until ECT SETTING

On the front panel ONLY:

1.Press SETTING repeatedly until “REAR DELAY” appears on the

display.

ECT SETTING

“CROSS OVER” appears on the display.

The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN ° CONTROL

The display changes to show the current setting.

2. Press CONTROL UP 5/DOWN °

CONTROL

to select the crossover frequency level according to the size of the small speaker connected.

DOWN UP

to select the delay time of the rear

speaker output (from 0 ms to

15 ms).

DOWN UP

Each time you press the button, the display changes to show the following:

80Hz100Hz120Hz

Notes:

Rear delay time is not valid for the DVD MULTI playback mode.

You cannot adjust the rear delay time when you have set “REAR SPK” to “NONE.”

• Use the following comments as reference when adjusting.

80Hz: Select this when the cone speaker unit built in the speaker is about 12 cm.

100Hz: Select this when the cone speaker unit built in the speaker is about 10 cm.

120Hz: Select this when the cone speaker unit built in the speaker is about 8 cm.

Note:

Crossover frequency is not valid for the DVD MULTI playback,

5 CH /4 CH Stereo, 3D-PHONIC, and HEADPHONE DSP modes.

18

Image 21
Contents LVT0618-004A RX-8010RBK / RX-8012RSLIf in Doubt Consult a Competent Electrician RX-8010RBK RX-8012RSL Table of Contents Parts Identification Remote Control Front PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM MW/LW Antennas Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers AM MW/LW Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker About the speaker impedanceVideo component connections Video camera TV and/or DBS tunerTo audio OutputDigital Connections Digital input terminalsDigital output terminal USB Connection Change the PC audio settingLamp on the USB Audio button lights up USB cablePutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Replace the coverBefore using the remote control Turning the Power On and Off StandbyBasic Operations Selecting the Source to PlayAdjusting the Volume Signal and speaker indicators on the displaySelecting different sources for picture and sound From the remote control only Listening at Night Midnight ModeSelecting the Front Speakers Muting the SoundActivating the Subwoofer Sound Attenuating the Input Signal Reinforcing the BassSelecting the Line Direct Function Adjusting the Equalization Patterns Using the Sleep TimerRecording a Source Basic Settings Adjusting the Front Speaker Output BalanceChanging the Source Name Setting the Subwoofer Information Adjusting the Subwoofer Output LevelSetting the Speakers for a Surround Field To select the delay time CTR Delay Center Delay Appears on the displayPress Setting repeatedly until ECT Setting Press Control UP 5/DOWN ControlPress Setting again until Digital Input Digital in Terminal SettingDigital 2/3/4 terminals setting appears on the display LFE ATT Low Frequency Effect Attenuator appears on DisplaySelecting the Analog or Digital Input Mode Press ANALOG/DIGITAL Input To change the input modeTo store the volume level Basic Setting and Adjustment Auto MemoryShowing the Text Information on Display Touch appears on the displayTuning in Stations Manually Using Preset TuningReceiving Radio Broadcasts Selecting the FM Reception Mode Press FM/AM Preset 5/untilPress FM Mode Press FM/AMWhat information can RDS signals provide? Using the RDS Radio Data System to Receive FM StationsTo search for a program using the PTY codes Searching for a Program by PTY CodesListening to an FM station Press PTY Search whilePress PTY Search while listening to an FM station FlashingPress EON so that the last selected Switching to a Broadcast Program Your Choice TemporarilyProgram type appears on Display Press TA/NEWS/INFO untilCreating a Surround Field in Your Room Surround modesDSP modes DSP Modes Available to Input Mode DVD Multi Playback ModeHeadphone DSP mode Reproducing the Sound FieldAvailable DSP modes Available DSP Modes According to the Speaker ArrangementAdjusting the Surround Modes Adjust the speaker output levels Adjust the center toneAdjusting the DAP Modes Adjust the liveness Adjust the room size sense of spaciousnessPress DSP Mode repeatedly until DAP mode you want to adjustAdjusting the Surround Modes with DAP Modes Liveness Adjust the speaker output levels Press Liveness to adjustAdjust the overall levels of the effect To select the effect level you wantPress DSP Mode repeatedly until DSP Mode Adjusting the 5 CH/4 CH Stereo ModePress DSP Mode repeatedly until Mode OnlyAdjusting the 3D-PHONIC Modes Memo Center tone level you wantActivating the DVD Multi Playback Mode Using the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the displayPress Menu Using the On-Screen MenusPress 5 / to move to Digital EQ Press 5 / to move to Sound CONTROL, then press 2Then press 2 CONTROL, then press 2Press 5/ to move to Sound CONTROL, then press 2 Press 5/ to move To Effect Adjust Then press 2Press 5/ to move To Midnight Select DVD Multi as the playing sourcePress 5/ to move to Tuner CONTROL, then press 2 Select FM or AM MW/LW as the playing sourceSelecting the Line Direct Function Selecting the Bass Boost FunctionPress 5/ to move To Setting Then press 2 Press 5/ to move To Preset MEMORY, then press 2Storing the Preset Stations Also see Setting the Basic Setting ItemsCompu Link Remote Control System Same timePress the play 3 button on the CD player CD player MD recorder Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerShowing the Disc Information on the TV Screen Press Text Display while CD or MD is selected as the sourceTo exit from the Disc information screen Press ExitPress 5 / to move to SEARCH, then Press Text Display while CD is selected as the sourcePress 5/ to move to SEARCH, then Press SET Press 5 / to move To Performer Then press SETPress 5 / to move To GENRE, then Press SET Press 5 / to move to SEARCH, then Press SETPress 5/ to move to Title Input Then press SET Entering the Disc InformationPress 5/ to move to the genre you want, then press SET Enter the disc title Referring to steps 3Press Text Display while MD is selected as the source For the CD Player with the disc memory functionOperating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section AmplifierCD changer CD playerTurntable CD recorderVCR 1 VCR connected to the VCR 1 jacks Operating Video ComponentsDVD player TV/VIDEOOperating Other Manufacturers’ Video Equipment If there are more than one code listed for your brand of TVRelease TV Try to operate your TV by pressing TVRelease CATV/DBS Release VCRTry to operate your VCR by pressing VCR Release Audio Problem Possible Cause Solution TroubleshootingOverload starts flashing on the display Amplifier SpecificationsAudio VideoFM tuner IHF Tuning Range Usable Sensitivity Signal-to-Noise RatioAM MW/LW tuner GeneralJVC 0401NHMMDWJEIN