JVC RX-8010RBK, RX-8012RSL Press Liveness to adjust, Liveness Adjust the speaker output levels

Page 38
DOLBY SURROUND

11.Press EFFECT to adjust the

EFFECT

overall level of the effect.

2

•Each time you press the button, the effect level changes as follows:

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5

EFFECT 4

As the number increases, DAP effect becomes stronger. (Normally set it to “EFFECT 3.”)

3. Press DSP MODE repeatedly until DSP MODE the DAP mode you want to adjust

—THEATER 1, THEATER 2, HALL 1, HALL 2, LIVE CLUB, DANCE CLUB, or PAVILION — appears on the display.

The DSP MODE lamp on the front panel button lights up, and the DSP indicator also lights up on the display.

12.Press ROOM SIZE to adjust the

ROOM

room size (sense of spaciousness).

 

SIZE

3

 

• Each time you press the button, the room

 

 

 

size changes as follows:

 

 

 

 

 

 

ROOMSIZE 1

 

ROOMSIZE 2

 

 

ROOMSIZE 3

 

 

 

 

ROOMSIZE 5

ROOMSIZE 4

 

 

 

 

As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. (Normally set it to “ROOMSIZE 3.”)

13.Press LIVENESS to adjust the

LIVENESS

liveness.

6

4.Adjust the speaker output levels.

1)Press LEVEL ADJUST repeatedly until one of the following indications appears on the display.

“CENTER”:

To adjust the center speaker level. “REAR L”:

To adjust the left rear speaker level. “REAR R”:

To adjust the right rear speaker level.

2)Press CONTROL UP 5/DOWN °to adjust the selected speaker output level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

AL LEVEL ADJUST

CONTROL

DOWN UP

•Each time you press the button, the liveness changes as follows:

LIVENESS 1 LIVENESS 2 LIVENESS 3

LIVENESS 5

LIVENESS 4

As the number increases, the attenuation level of reflections over time decreases so that acoustics change from “Dead” to “Live.” (Normally set it to “LIVENESS 3.”)

5.Adjust the center tone.

1)Press EFFECT repeatedly until “CTR TONE” appears on the display.

The display shows the current setting.

2)Press CONTROL UP 5/DOWN ° to select the center tone level you want.

•Each time you press the button, the display changes to show the following:

EFFECT SETTIN

CONTROL

DOWN UP

On the front panel:

You can also use the buttons on the front panel to adjust the sound with a Surround mode and a DAP mode. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

2. Press SURROUND ON/OFF to SURROUND ON/OFF activate an appropriate Surround

mode — PRO LOGIC, DOLBY DIGITAL or DTS SURROUND.

The SURROUND ON/OFF lamp on the front panel button lights up.

•Each time you press the button, the Surround mode turns on and off alternately.

•When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

CTR TONE 1 CTR TONE 2 CTR TONE 3

(Softer)(Soft)(Flat)

CTR TONE 5

 

CTR TONE 4

 

(Sharper)

 

(Sharp)

To make the dialogue softer, select “CTR TONE 1” or

“CTR TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or

“CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

6. Adjust the overall levels of the effect.

1)

Press EFFECT repeatedly until

EFFECT

SETT

 

“EFFECT” appears on the display.

 

 

 

 

 

 

The display shows the current setting.

 

 

2)

Press CONTROL UP 5/DOWN °

CONTROL

 

to select the effect level you want.

 

DOWN UP

•Each time you press the button, the display changes to show the following:

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5

EFFECT 4

As the number increases, DAP effect becomes stronger. (Normally set it to “EFFECT 3.”)

35

Page 37 Page 39
Image 38
Page 37 Page 39
Contents RX-8010RBK / RX-8012RSL LVT0618-004AIf in Doubt Consult a Competent Electrician RX-8010RBK RX-8012RSL Table of Contents Remote Control Front Panel Parts IdentificationConnecting the FM and AM MW/LW Antennas Before InstallationChecking the Supplied Accessories Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM MW/LW Antenna ConnectionsConnecting the subwoofer speaker Connecting Audio/Video ComponentsConnecting the rear and center speakers About the speaker impedanceVideo component connections To audio TV and/or DBS tunerVideo camera OutputDigital output terminal Digital ConnectionsDigital input terminals Lamp on the USB Audio button lights up Change the PC audio settingUSB Connection USB cablePlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Replace the coverBasic Operations Turning the Power On and Off StandbyBefore using the remote control Selecting the Source to PlaySelecting different sources for picture and sound Adjusting the VolumeSignal and speaker indicators on the display Selecting the Front Speakers Listening at Night Midnight ModeFrom the remote control only Muting the SoundSelecting the Line Direct Function Activating the Subwoofer Sound Attenuating the Input SignalReinforcing the Bass Recording a Source Adjusting the Equalization PatternsUsing the Sleep Timer Changing the Source Name Basic SettingsAdjusting the Front Speaker Output Balance Setting the Speakers for a Surround Field Setting the Subwoofer InformationAdjusting the Subwoofer Output Level Press Setting repeatedly until ECT Setting CTR Delay Center Delay Appears on the displayTo select the delay time Press Control UP 5/DOWN ControlDigital 2/3/4 terminals setting appears on the display Digital Input Digital in Terminal SettingPress Setting again until LFE ATT Low Frequency Effect Attenuator appears on DisplaySelecting the Analog or Digital Input Mode To change the input mode Press ANALOG/DIGITAL InputShowing the Text Information on Display Basic Setting and Adjustment Auto MemoryTo store the volume level Touch appears on the displayReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Press FM Mode Press FM/AM Preset 5/untilSelecting the FM Reception Mode Press FM/AMTo search for a program using the PTY codes Using the RDS Radio Data System to Receive FM StationsWhat information can RDS signals provide? Searching for a Program by PTY CodesPress PTY Search while listening to an FM station Press PTY Search whileListening to an FM station FlashingProgram type appears on Display Switching to a Broadcast Program Your Choice TemporarilyPress EON so that the last selected Press TA/NEWS/INFO untilDSP modes Creating a Surround Field in Your RoomSurround modes Headphone DSP mode DVD Multi Playback ModeDSP Modes Available to Input Mode Reproducing the Sound FieldAvailable DSP Modes According to the Speaker Arrangement Available DSP modesAdjusting the Surround Modes Adjusting the DAP Modes Adjust the speaker output levelsAdjust the center tone Press DSP Mode repeatedly until Adjust the room size sense of spaciousnessAdjust the liveness DAP mode you want to adjustAdjusting the Surround Modes with DAP Modes Adjust the overall levels of the effect Press Liveness to adjustLiveness Adjust the speaker output levels To select the effect level you wantPress DSP Mode repeatedly until Mode Adjusting the 5 CH/4 CH Stereo ModePress DSP Mode repeatedly until DSP Mode OnlyAdjusting the 3D-PHONIC Modes Center tone level you want MemoPress DVD Multi so that DVD Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Multi appears on the displayUsing the On-Screen Menus Press MenuThen press 2 Press 5 / to move to Sound CONTROL, then press 2Press 5 / to move to Digital EQ CONTROL, then press 2Press 5/ to move To Midnight Press 5/ to move To Effect Adjust Then press 2Press 5/ to move to Sound CONTROL, then press 2 Select DVD Multi as the playing sourceSelecting the Line Direct Function Select FM or AM MW/LW as the playing sourcePress 5/ to move to Tuner CONTROL, then press 2 Selecting the Bass Boost FunctionStoring the Preset Stations Also see Press 5/ to move To Preset MEMORY, then press 2Press 5/ to move To Setting Then press 2 Setting the Basic Setting ItemsPress the play 3 button on the CD player Compu Link Remote Control SystemSame time Displaying the Disc Information on the TV screen Text Compu Link Remote Control SystemCD player MD recorder Disc Search Only for CD PlayerTo exit from the Disc information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen Press ExitPress 5/ to move to SEARCH, then Press SET Press Text Display while CD is selected as the sourcePress 5 / to move to SEARCH, then Press 5 / to move To Performer Then press SETPress 5/ to move to Title Input Then press SET Press 5 / to move to SEARCH, then Press SETPress 5 / to move To GENRE, then Press SET Entering the Disc InformationPress Text Display while MD is selected as the source Enter the disc title Referring to steps 3Press 5/ to move to the genre you want, then press SET For the CD Player with the disc memory functionTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierTurntable CD playerCD changer CD recorderDVD player Operating Video ComponentsVCR 1 VCR connected to the VCR 1 jacks TV/VIDEORelease TV If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Try to operate your TV by pressing TVTry to operate your VCR by pressing VCR Release CATV/DBSRelease VCR Release Audio Troubleshooting Problem Possible Cause SolutionOverload starts flashing on the display Audio SpecificationsAmplifier VideoAM MW/LW tuner Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF GeneralJVC 0401NHMMDWJEIN
Top Page Image Contents