JVC RX-8012RSL Connecting the Speakers, AM MW/LW Antenna Connections, Basic connecting procedure

Page 7

AM (MW/LW) Antenna Connections

Snap the tabs on the loop into the

	ANTENNA	slots of the base to assemble the
	FM 75
		AM (MW/LW) loop.
	COAXIAL

AM	AM (MW/LW)
LOOP	AM (MW/LW)
AM	Loop Antenna
EXT

123

Outdoor single vinyl-covered wire (not supplied)

Turn the loop until you have the best reception.

Notes:

• If the AM (MW/LW) loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram.

•Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

•If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM (MW/LW) loop antenna connected.)

Connecting the Speakers

You can connect the following speakers:

•Two pairs of front speakers to produce normal stereo sound.

•One pair of rear speakers to enjoy the surround effect.

•One center speaker to produce more effective surround effect (to emphasize human voices).

•One subwoofer to enhance the bass.

IMPORTANT:

After connecting the speakers listed above, set the speaker setting information properly to obtain the best possible Surround and DSP effect. For details, see page 17.

For each speaker (except for a subwoofer), connect the (+) and (–) terminals on the rear panel to the (+) and (–) terminals marked on the speakers. For connecting a subwoofer, see page 5.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.

Basic connecting procedure

1

2

3

4

1Cut, twist and remove the insulation at the end of each speaker signal cable (not supplied).

2Turn the knob counterclockwise.

3Insert the speaker signal cable.

4Turn the knob clockwise.

Connecting the front speakers

You can connect two pairs of front speakers (one pair to the FRONT SPEAKERS 1 terminals, and another pair to the FRONT SPEAKERS 2 terminals).

Right speaker		FRONT SPEAKERS 1		Left speaker

FRONT SPEAKERS
RIGHT 2 LEFT	RIGHT 1 LEFT	CAUTION : SPEAKER IMPEDANCE
	+	1	OR	2 : 8	16
		1	AND	2 : 16	32

–

Right speaker		FRONT SPEAKERS 2		Left speaker

4

Image 7

Contents LVT0618-004A RX-8010RBK / RX-8012RSLIf in Doubt Consult a Competent Electrician RX-8010RBK RX-8012RSL Table of Contents Parts Identification Remote Control Front PanelGetting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM MW/LW AntennasAM MW/LW Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersAbout the speaker impedance Connecting Audio/Video ComponentsConnecting the rear and center speakers Connecting the subwoofer speakerVideo component connections Output TV and/or DBS tunerVideo camera To audioDigital input terminals Digital ConnectionsDigital output terminal USB cable Change the PC audio settingUSB Connection Lamp on the USB Audio button lights upReplace the cover Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletSelecting the Source to Play Turning the Power On and Off StandbyBefore using the remote control Basic OperationsSignal and speaker indicators on the display Adjusting the VolumeSelecting different sources for picture and sound Muting the Sound Listening at Night Midnight ModeFrom the remote control only Selecting the Front SpeakersReinforcing the Bass Activating the Subwoofer Sound Attenuating the Input SignalSelecting the Line Direct Function Using the Sleep Timer Adjusting the Equalization PatternsRecording a Source Adjusting the Front Speaker Output Balance Basic SettingsChanging the Source Name Adjusting the Subwoofer Output Level Setting the Subwoofer InformationSetting the Speakers for a Surround Field Press Control UP 5/DOWN Control CTR Delay Center Delay Appears on the displayTo select the delay time Press Setting repeatedly until ECT SettingLFE ATT Low Frequency Effect Attenuator appears on Display Digital Input Digital in Terminal SettingPress Setting again until Digital 2/3/4 terminals setting appears on the displaySelecting the Analog or Digital Input Mode Press ANALOG/DIGITAL Input To change the input modeTouch appears on the display Basic Setting and Adjustment Auto MemoryTo store the volume level Showing the Text Information on DisplayUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Press FM/AM Press FM/AM Preset 5/untilSelecting the FM Reception Mode Press FM ModeSearching for a Program by PTY Codes Using the RDS Radio Data System to Receive FM StationsWhat information can RDS signals provide? To search for a program using the PTY codesFlashing Press PTY Search whileListening to an FM station Press PTY Search while listening to an FM stationPress TA/NEWS/INFO until Switching to a Broadcast Program Your Choice TemporarilyPress EON so that the last selected Program type appears on DisplaySurround modes Creating a Surround Field in Your RoomDSP modes Reproducing the Sound Field DVD Multi Playback ModeDSP Modes Available to Input Mode Headphone DSP modeAvailable DSP modes Available DSP Modes According to the Speaker ArrangementAdjusting the Surround Modes Adjust the center tone Adjust the speaker output levelsAdjusting the DAP Modes DAP mode you want to adjust Adjust the room size sense of spaciousnessAdjust the liveness Press DSP Mode repeatedly untilAdjusting the Surround Modes with DAP Modes To select the effect level you want Press Liveness to adjustLiveness Adjust the speaker output levels Adjust the overall levels of the effectOnly Adjusting the 5 CH/4 CH Stereo ModePress DSP Mode repeatedly until DSP Mode Press DSP Mode repeatedly until ModeAdjusting the 3D-PHONIC Modes Memo Center tone level you wantMulti appears on the display Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Press DVD Multi so that DVDPress Menu Using the On-Screen MenusCONTROL, then press 2 Press 5 / to move to Sound CONTROL, then press 2Press 5 / to move to Digital EQ Then press 2Select DVD Multi as the playing source Press 5/ to move To Effect Adjust Then press 2Press 5/ to move to Sound CONTROL, then press 2 Press 5/ to move To MidnightSelecting the Bass Boost Function Select FM or AM MW/LW as the playing sourcePress 5/ to move to Tuner CONTROL, then press 2 Selecting the Line Direct FunctionSetting the Basic Setting Items Press 5/ to move To Preset MEMORY, then press 2Press 5/ to move To Setting Then press 2 Storing the Preset Stations Also seeSame time Compu Link Remote Control SystemPress the play 3 button on the CD player Disc Search Only for CD Player Text Compu Link Remote Control SystemCD player MD recorder Displaying the Disc Information on the TV screenPress Exit Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen To exit from the Disc information screenPress 5 / to move To Performer Then press SET Press Text Display while CD is selected as the sourcePress 5 / to move to SEARCH, then Press 5/ to move to SEARCH, then Press SETEntering the Disc Information Press 5 / to move to SEARCH, then Press SETPress 5 / to move To GENRE, then Press SET Press 5/ to move to Title Input Then press SETFor the CD Player with the disc memory function Enter the disc title Referring to steps 3Press 5/ to move to the genre you want, then press SET Press Text Display while MD is selected as the sourceSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder CD playerCD changer TurntableTV/VIDEO Operating Video ComponentsVCR 1 VCR connected to the VCR 1 jacks DVD playerTry to operate your TV by pressing TV If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Release TVRelease VCR Release CATV/DBSTry to operate your VCR by pressing VCR Release Audio Problem Possible Cause Solution TroubleshootingOverload starts flashing on the display Video SpecificationsAmplifier AudioGeneral Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF AM MW/LW tunerJVC 0401NHMMDWJEIN