JVC RX-8010RBK, RX-8012RSL manual Adjusting the Surround Modes

Page 34
DOLBY SURROUND

Adjusting the Surround Modes

You can also use a Surround mode with a DAP mode (see page 34).

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 17).

5.Select the speaker you want to adjust.

•To select the center speaker level, press CENTER. “CTR” appears on the remote control display window.

•To select the left rear speaker level, press REAR L. “REARL” appears on the remote control display window.

•To select the right rear speaker level, press REAR R. “REARR” appears on the remote control display window.

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 3 again.

• You cannot adjust the rear speaker output levels when you have set

“REAR SPK” to “NONE.” See page 17.

• You cannot adjust the center speaker output level and center tone

when you have set “CTR SPK” to “NONE.” See page 17.

• To adjust the front speaker output balance and subwoofer output

level, see pages 16 and 17.

∗CENTER

∗REARL

∗REARR

9

0

+10

FMMODE100+

6.Press LEVEL +/– to adjust the speaker output levels (–10 dB to +10 dB).

+∗BAL L

CH/∗LEVEL

−∗BAL R

From the remote control:

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with

 

 

DOLBY SURROUND

mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

2. Press SURROUND ON/OFF to

SURROUND

 

activate an appropriate Surround

ON/OFF

 

mode — PRO LOGIC, DOLBY

 

DIGITAL or DTS SURROUND.

 

The SURROUND ON/OFF lamp on the front panel button lights up.

•Each time you press the button, the Surround mode turns on and off alternately.

•When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

7.

Press SOUND.

SOUND

 

• To adjust other speaker output levels, repeat

 

 

steps 5 and 6.

 

8.

Press TEST again to stop the test

TEST

4

 

tone.

 

 

9.

Press CTR TONE to select the

CTRTONE

 

center tone level you want.

5

ENTER

The center tone adjustment affects the mid- frequency range, which the human voice is mostly made up of.

•Each time you press the button, the display changes to show the following:

CTR TONE 1 CTR TONE 2 CTR TONE 3

(Softer)(Soft)(Flat)

CTR TONE 5

 

CTR TONE 4

 

(Sharper)

 

(Sharp)

To make the dialogue softer, select “CTR TONE 1” or “CTR

3. Press SOUND.

The 10 keys are activated for sound adjustments.

4. Press TEST to check the speaker output balance.

“TEST TONE L” starts flashing on the display, and a test tone comes out of the speakers in the following order:

SOUND

TEST

4

TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

 

TEST TONE L

 

TEST TONE C

 

TEST TONE R

 

 

(Left front speaker)

(Center speaker)

(Right front speaker)

 

 

TEST TONE LS

 

 

TEST TONE RS

 

 

(Left rear speaker)

 

 

(Right rear speaker)

 

 

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CTR SPK” is set to “NONE” (see page 17).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 17).

•If the TV is turned on and the proper video input is selected on the TV, the test tone screen will appear on the TV.

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

31

Page 33 Page 35
Image 34
Page 33 Page 35
Contents RX-8010RBK / RX-8012RSL LVT0618-004AIf in Doubt Consult a Competent Electrician RX-8010RBK RX-8012RSL Table of Contents Remote Control Front Panel Parts IdentificationConnecting the FM and AM MW/LW Antennas Before InstallationChecking the Supplied Accessories Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM MW/LW Antenna ConnectionsConnecting the subwoofer speaker Connecting Audio/Video ComponentsConnecting the rear and center speakers About the speaker impedanceVideo component connections To audio TV and/or DBS tunerVideo camera OutputDigital input terminals Digital ConnectionsDigital output terminal Lamp on the USB Audio button lights up Change the PC audio settingUSB Connection USB cablePlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control Replace the coverBasic Operations Turning the Power On and Off StandbyBefore using the remote control Selecting the Source to PlaySignal and speaker indicators on the display Adjusting the VolumeSelecting different sources for picture and sound Selecting the Front Speakers Listening at Night Midnight ModeFrom the remote control only Muting the SoundReinforcing the Bass Activating the Subwoofer Sound Attenuating the Input SignalSelecting the Line Direct Function Using the Sleep Timer Adjusting the Equalization PatternsRecording a Source Adjusting the Front Speaker Output Balance Basic SettingsChanging the Source Name Adjusting the Subwoofer Output Level Setting the Subwoofer InformationSetting the Speakers for a Surround Field Press Setting repeatedly until ECT Setting CTR Delay Center Delay Appears on the displayTo select the delay time Press Control UP 5/DOWN ControlDigital 2/3/4 terminals setting appears on the display Digital Input Digital in Terminal SettingPress Setting again until LFE ATT Low Frequency Effect Attenuator appears on DisplaySelecting the Analog or Digital Input Mode To change the input mode Press ANALOG/DIGITAL InputShowing the Text Information on Display Basic Setting and Adjustment Auto MemoryTo store the volume level Touch appears on the displayUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Press FM Mode Press FM/AM Preset 5/untilSelecting the FM Reception Mode Press FM/AMTo search for a program using the PTY codes Using the RDS Radio Data System to Receive FM StationsWhat information can RDS signals provide? Searching for a Program by PTY CodesPress PTY Search while listening to an FM station Press PTY Search whileListening to an FM station FlashingProgram type appears on Display Switching to a Broadcast Program Your Choice TemporarilyPress EON so that the last selected Press TA/NEWS/INFO untilSurround modes Creating a Surround Field in Your RoomDSP modes Headphone DSP mode DVD Multi Playback ModeDSP Modes Available to Input Mode Reproducing the Sound FieldAvailable DSP Modes According to the Speaker Arrangement Available DSP modesAdjusting the Surround Modes Adjust the center tone Adjust the speaker output levelsAdjusting the DAP Modes Press DSP Mode repeatedly until Adjust the room size sense of spaciousnessAdjust the liveness DAP mode you want to adjustAdjusting the Surround Modes with DAP Modes Adjust the overall levels of the effect Press Liveness to adjustLiveness Adjust the speaker output levels To select the effect level you wantPress DSP Mode repeatedly until Mode Adjusting the 5 CH/4 CH Stereo ModePress DSP Mode repeatedly until DSP Mode OnlyAdjusting the 3D-PHONIC Modes Center tone level you want MemoPress DVD Multi so that DVD Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Multi appears on the displayUsing the On-Screen Menus Press MenuThen press 2 Press 5 / to move to Sound CONTROL, then press 2Press 5 / to move to Digital EQ CONTROL, then press 2Press 5/ to move To Midnight Press 5/ to move To Effect Adjust Then press 2Press 5/ to move to Sound CONTROL, then press 2 Select DVD Multi as the playing sourceSelecting the Line Direct Function Select FM or AM MW/LW as the playing sourcePress 5/ to move to Tuner CONTROL, then press 2 Selecting the Bass Boost FunctionStoring the Preset Stations Also see Press 5/ to move To Preset MEMORY, then press 2Press 5/ to move To Setting Then press 2 Setting the Basic Setting ItemsSame time Compu Link Remote Control SystemPress the play 3 button on the CD player Displaying the Disc Information on the TV screen Text Compu Link Remote Control SystemCD player MD recorder Disc Search Only for CD PlayerTo exit from the Disc information screen Press Text Display while CD or MD is selected as the sourceShowing the Disc Information on the TV Screen Press ExitPress 5/ to move to SEARCH, then Press SET Press Text Display while CD is selected as the sourcePress 5 / to move to SEARCH, then Press 5 / to move To Performer Then press SETPress 5/ to move to Title Input Then press SET Press 5 / to move to SEARCH, then Press SETPress 5 / to move To GENRE, then Press SET Entering the Disc InformationPress Text Display while MD is selected as the source Enter the disc title Referring to steps 3Press 5/ to move to the genre you want, then press SET For the CD Player with the disc memory functionTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierTurntable CD playerCD changer CD recorderDVD player Operating Video ComponentsVCR 1 VCR connected to the VCR 1 jacks TV/VIDEORelease TV If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Try to operate your TV by pressing TVRelease VCR Release CATV/DBSTry to operate your VCR by pressing VCR Release Audio Troubleshooting Problem Possible Cause SolutionOverload starts flashing on the display Audio SpecificationsAmplifier VideoAM MW/LW tuner Tuning Range Usable Sensitivity Signal-to-Noise RatioFM tuner IHF GeneralJVC 0401NHMMDWJEIN
Top Page Image Contents