JVC RX-8012RSL, RX-8010RBK manual Overload starts flashing on the display

Page 61

PROBLEM	POSSIBLE CAUSE	SOLUTION

“OVERLOAD” starts flashing on the display.


Speakers are overloaded because of high	1.	Press STANDBY/ON				on the front
volume.		panel to turn off the receiver.
	2.	Stop the playback source.
	3.	Turn on the receiver again, and adjust the
		volume.

Speakers are overloaded because of short	Press STANDBY/ON					on the front panel,


circuit of speaker terminals.	then check the speaker wiring.
	If “OVERLOAD” does not disappear, unplug
	the AC power cord, then plug it back again.

If speaker wiring is not short-circuited, contact your dealer.

The STANDBY lamp lights up after turning on the power, but soon the receiver turns off again (into standby mode).

The receiver is overloaded because of a high voltage.

Press STANDBY/ON on the front panel to turn off the receiver. After unplugging the AC power cord, consult your dealer.

Remote control does not work.

There is an obstruction in front of the	Remove the obstruction.
remote sensor on the receiver.

Batteries are weak.

Replace batteries. (See page 10.)

Remote control does not work intendedly.

An incorrect remote control operation mode is selected.

Select the correct remote control operation mode. (See page 51 – 56.)

58

Image 61

Contents LVT0618-004A RX-8010RBK / RX-8012RSLIf in Doubt Consult a Competent Electrician RX-8010RBK RX-8012RSL Table of Contents Parts Identification Remote Control Front PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM MW/LW Antennas Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers AM MW/LW Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker About the speaker impedanceVideo component connections Video camera TV and/or DBS tunerTo audio OutputDigital input terminals Digital ConnectionsDigital output terminal USB Connection Change the PC audio settingLamp on the USB Audio button lights up USB cablePutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Replace the coverBefore using the remote control Turning the Power On and Off StandbyBasic Operations Selecting the Source to PlaySignal and speaker indicators on the display Adjusting the VolumeSelecting different sources for picture and sound From the remote control only Listening at Night Midnight ModeSelecting the Front Speakers Muting the SoundReinforcing the Bass Activating the Subwoofer Sound Attenuating the Input SignalSelecting the Line Direct Function Using the Sleep Timer Adjusting the Equalization PatternsRecording a Source Adjusting the Front Speaker Output Balance Basic SettingsChanging the Source Name Adjusting the Subwoofer Output Level Setting the Subwoofer InformationSetting the Speakers for a Surround Field To select the delay time CTR Delay Center Delay Appears on the displayPress Setting repeatedly until ECT Setting Press Control UP 5/DOWN ControlPress Setting again until Digital Input Digital in Terminal SettingDigital 2/3/4 terminals setting appears on the display LFE ATT Low Frequency Effect Attenuator appears on DisplaySelecting the Analog or Digital Input Mode Press ANALOG/DIGITAL Input To change the input modeTo store the volume level Basic Setting and Adjustment Auto MemoryShowing the Text Information on Display Touch appears on the displayUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode Press FM/AM Preset 5/untilPress FM Mode Press FM/AMWhat information can RDS signals provide? Using the RDS Radio Data System to Receive FM StationsTo search for a program using the PTY codes Searching for a Program by PTY CodesListening to an FM station Press PTY Search whilePress PTY Search while listening to an FM station FlashingPress EON so that the last selected Switching to a Broadcast Program Your Choice TemporarilyProgram type appears on Display Press TA/NEWS/INFO untilSurround modes Creating a Surround Field in Your RoomDSP modes DSP Modes Available to Input Mode DVD Multi Playback ModeHeadphone DSP mode Reproducing the Sound FieldAvailable DSP modes Available DSP Modes According to the Speaker ArrangementAdjusting the Surround Modes Adjust the center tone Adjust the speaker output levelsAdjusting the DAP Modes Adjust the liveness Adjust the room size sense of spaciousnessPress DSP Mode repeatedly until DAP mode you want to adjustAdjusting the Surround Modes with DAP Modes Liveness Adjust the speaker output levels Press Liveness to adjustAdjust the overall levels of the effect To select the effect level you wantPress DSP Mode repeatedly until DSP Mode Adjusting the 5 CH/4 CH Stereo ModePress DSP Mode repeatedly until Mode OnlyAdjusting the 3D-PHONIC Modes Memo Center tone level you wantActivating the DVD Multi Playback Mode Using the DVD Multi Playback ModePress DVD Multi so that DVD Multi appears on the displayPress Menu Using the On-Screen MenusPress 5 / to move to Digital EQ Press 5 / to move to Sound CONTROL, then press 2Then press 2 CONTROL, then press 2Press 5/ to move to Sound CONTROL, then press 2 Press 5/ to move To Effect Adjust Then press 2Press 5/ to move To Midnight Select DVD Multi as the playing sourcePress 5/ to move to Tuner CONTROL, then press 2 Select FM or AM MW/LW as the playing sourceSelecting the Line Direct Function Selecting the Bass Boost FunctionPress 5/ to move To Setting Then press 2 Press 5/ to move To Preset MEMORY, then press 2Storing the Preset Stations Also see Setting the Basic Setting ItemsSame time Compu Link Remote Control SystemPress the play 3 button on the CD player CD player MD recorder Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerShowing the Disc Information on the TV Screen Press Text Display while CD or MD is selected as the sourceTo exit from the Disc information screen Press ExitPress 5 / to move to SEARCH, then Press Text Display while CD is selected as the sourcePress 5/ to move to SEARCH, then Press SET Press 5 / to move To Performer Then press SETPress 5 / to move To GENRE, then Press SET Press 5 / to move to SEARCH, then Press SETPress 5/ to move to Title Input Then press SET Entering the Disc InformationPress 5/ to move to the genre you want, then press SET Enter the disc title Referring to steps 3Press Text Display while MD is selected as the source For the CD Player with the disc memory functionOperating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section AmplifierCD changer CD playerTurntable CD recorderVCR 1 VCR connected to the VCR 1 jacks Operating Video ComponentsDVD player TV/VIDEOOperating Other Manufacturers’ Video Equipment If there are more than one code listed for your brand of TVRelease TV Try to operate your TV by pressing TVRelease VCR Release CATV/DBSTry to operate your VCR by pressing VCR Release Audio Problem Possible Cause Solution TroubleshootingOverload starts flashing on the display Amplifier SpecificationsAudio VideoFM tuner IHF Tuning Range Usable Sensitivity Signal-to-Noise RatioAM MW/LW tuner GeneralJVC 0401NHMMDWJEIN