4.Adjust the overall levels of the effect.
1)Press EFFECT repeatedly until “EFFECT” appears on the display. The display shows the current setting.
2)Press CONTROL UP 5/DOWN ° to select the effect level you want.
•Each time you press the button, the display changes to show the following:
EFFECT SETT
CONTROL
DOWN UP
3.Select the speaker you want to adjust.
•To select the center speaker level, press CENTER. “CTR” appears on the remote control display window.
•To select the left rear speaker level, press REAR L. “REARL” appears on the remote control display window.
•To select the right rear speaker level, press REAR R. “REARR” appears on the remote control display window.
∗CENTER | ∗REARL | ∗REARR |
9 | 0 |
|
EFFECT 1 
EFFECT 2 
EFFECT 3 
EFFECT 5 | EFFECT 4 |
As the number increases, the selected DAP effect becomes stronger. (Normally set it to “EFFECT 3.”)
5. Adjust the room size (sense of spaciousness).
1) | Press EFFECT repeatedly until | EFFECT |
| SETTIN | |
| “ROOMSIZE” appears on the display. |
|
|
| |
|
|
|
| ||
| The display shows the current setting. |
|
|
| |
|
|
|
| ||
2) | Press CONTROL UP 5/DOWN °to |
|
|
| |
CONTROL | |||||
| select the room size you want. | ||||
| • Each time you press the button, the | DOWN | UP | ||
|
|
|
| ||
| display changes to show the following: |
|
|
| |
+10 |
FMMODE100+
4.Press LEVEL +/– to adjust the speaker output levels
5.Press SOUND.
•To adjust other speaker output levels, repeat steps 3 and 4.
6.Press CTR TONE to select the center tone level you want.
•Each time you press the button, the display changes to show the following:
+∗BAL L
CH/∗LEVEL
−∗BAL R
SOUND
CTRTONE
5
ENTER
ROOMSIZE 1 |
| ROOMSIZE 2 |
| ROOMSIZE 3 |
| ||
|
|
| |||||
ROOMSIZE 5 | ROOMSIZE 4 |
|
| ||||
|
| ||||||
As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. (Normally set it to “ROOMSIZE 3.”)
CTR TONE 1 
CTR TONE 2 
CTR TONE 3
(Softer)(Soft)(Flat)
CTR TONE 5 |
| CTR TONE 4 |
| ||
(Sharper) |
| (Sharp) |
To make the dialogue softer, select “CTR TONE 1” or “CTR
TONE 2.”
To make the dialogue clearer, select “CTR TONE 4” or “CTR TONE 5.”
6.Adjust the liveness.
1)Press EFFECT repeatedly until “LIVENESS” appears on the display. The display shows the current setting.
2)Press CONTROL UP 5/DOWN °to select the liveness level you want.
•Each time you press the button, the display changes to show the following:
EFFECT SETT
CONTROL
DOWN UP
When “CTR TONE 3” is selected, no adjustment is applied.
7. Press EFFECT to adjust the | EFFECT |
overall level of the effect. | 2 |
|
•Each time you press the button, the effect level changes as follows:
EFFECT 1 
EFFECT 2 
EFFECT 3
EFFECT 5 | EFFECT 4 |
LIVENESS 1 
LIVENESS 2 
LIVENESS 3 
LIVENESS 5 | LIVENESS 4 |
As the number increases, the attenuation level of reflections over time decreases so that acoustics change from “Dead” to “Live.” (Normally set it to “LIVENESS 3.”)
From the remote control:
1. Press DSP MODE repeatedly until the | DSP | |
MODE | ||
DAP mode you want to adjust — | ||
| ||
THEATER 1, THEATER 2, HALL 1, |
| |
HALL 2, LIVE CLUB, DANCE CLUB, or | ||
PAVILION — appears on the display. |
| |
The DSP MODE lamp on the front panel button lights up, and the DSP indicator also lights up on the display.
•When you have set “REAR SPK” to “NONE,” the 3D- PHONIC indicator also lights up.
2. Press SOUND. | SOUND |
The 10 keys are activated for sound adjustments.
As the number increases, the selected DAP effect becomes stronger. (Normally set it to “EFFECT 3.”)
8. Press ROOM SIZE to adjust the | ROOM | ||||||
room size (sense of spaciousness). | SIZE | ||||||
3 |
| ||||||
• Each time you press the button, the room |
|
| |||||
size changes as follows: |
|
|
|
|
| ||
ROOMSIZE 1 |
| ROOMSIZE 2 |
| ROOMSIZE 3 |
| ||
|
|
| |||||
ROOMSIZE 5 | ROOMSIZE 4 |
|
| ||||
|
| ||||||
As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. (Normally set it to “ROOMSIZE 3.”)
33