Weider 831.14622.0 user manual Arm Assembly, See the left inset drawing. Attach the Lock Plate

Page 12

Arm Assembly

9.Attach the Butterfly Frame Brace (6) to the Upright (2) with two M8 x 80mm Bolts (100), two M8 Washers (103), and two M8 Nylon Locknuts (78). Do not tighten the Nylon Locknuts yet.

10.Apply grease in the locations shown. Insert a 56.5mm Spacer (69) the indicated hole in the Leg Lever (12). Attach the Leg Lever to the Front Leg (10) with an M10 x 61mm Bolt Set (116). Make sure the indicated rod is oriented as shown.

See the left inset drawing. Attach the Lock Plate

(14)to the Front Leg (10) with the M8 x 69mm Shoulder Bolt (87), an M8 Washer (103), and an M8 Nylon Locknut (78).

See the right inset drawing. Insert the Lock Plate Pin (95) through the Lock Plate (14) and the Leg Lever (12). Attach the tether on the Lock Plate Pin to the Front Leg (10) with an M4 x 12mm Self-tapping Screw (102).

11.Attach the Butterfly Frame (5) to the Top Frame

(4) with two M8 x 80mm Bolts (100), two M8 Washers (103), and two M8 Nylon Locknuts (78).

Do not tighten the Nylon Locknuts yet.

Attach the Butterfly Frame (5) to the Butterfly Frame Brace (6) with an M10 x 75mm Button Screw (118).

9

 

 

 

 

 

78

 

100

 

 

 

 

 

103

 

6

100

 

 

 

2

 

 

10

 

Grease

 

 

 

 

 

Hole

116

 

 

 

 

Grease

 

 

 

69

 

116

 

12

 

 

 

 

10

 

 

Rod

 

 

 

 

103

 

 

10

14

 

 

 

 

14

 

78

 

 

102

12

 

 

95

 

87

 

10

 

 

 

 

11

 

 

 

 

100

 

 

 

 

103

 

 

103

 

 

 

4

 

 

5

 

 

 

 

 

6

 

 

 

78

 

118

 

 

 

12

Image 12
Contents Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions Before YOU Begin Right SideLeft Side Part Identification CHART-Model No .14622.0 R1006A M10 x 61mm Bolt Set Part Identification CHART-Model No .14622.0 R1006A Assembly Make Assembly Easier for YourselfFrame Assembly Nylon Locknuts yetNylon Locknuts 78. Do not tighten the Nylon Locknuts yet End of the Leg Lever Bumper is pointing upRepeat this step for the Right Shroud See the inset drawing and attach the other Shroud Cover 23 in the same manner This step clearlyArm Assembly See the left inset drawing. Attach the Lock PlateDo not tighten the Nylon Locknuts yet Repeat this step for the Left Butterfly Arm Repeat this step for the Left Press Arm not shown Tighten the Nylon Locknuts 77 used in step BendCable Assembly Grease Flat Edge Page Page Page Page Cable Trap and Half Guards are oriented as shown Seat Assembly Repeat this step for the Left Butterfly PadKnob passes through one of the holes in the Backrest Frame Page Page Adjustments Changing the Weight SettingAttaching the Accessories Using the Curl PAD Adjusting the BackrestSeat 32 can be adjusted in the same manner Locking the Weight StackWeight Resistance Chart Weight High Butterfly Press ARM LEG Lever LOW PulleyLocking the LEG Lever LbsCable Diagram Maintenance Tightening the CablesExercise Guidelines Muscle Chart Cooling DownStaying Motivated Exercise Weight Sets Reps DateAerobic Exercise Thursday Aerobic Exercise DatePart LIST-Model No Key Qty DescriptionExploded DRAWING-Model No R1006AExploded DRAWING-Model No DAY Full Warranty Get it fixed, at your home or ours