Weider PRO 375 user manual Assembly, Make Things Easier for Yourself, Locknuts yet

Page 5

ASSEMBLY

Make Things Easier for Yourself

Everything in this manual is designed to ensure that the weight bench can be assembled suc- cessfully by anyone. However, it is important to realize that the versatile weight bench has many parts and that the assembly process will take time. Most people find that by setting aside plen- ty of time, assembly will go smoothly.

Before beginning assembly, carefully read the following information and instructions:

Assembly requires two people.

Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.

Tighten all parts as you assemble them, unless instructed to do otherwise.

As you assemble the weight bench, make sure all parts are oriented as shown in the drawings.

For help identifying small parts, refer to the PART IDENTIFICATION CHART.

The following tools (not included) are required for assembly:

• Two adjustable wrenches

• One rubber mallet

• One standard screwdriver

• One Phillips screwdriver

Lubricant, such as grease or petroleum jelly, and soapy water.

Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

1.Before beginning, make sure you understand the information in the box above. Note: Some parts described in the assembly steps may be pre-assembled.

Press a 60mm Square Inner Cap (55) into each end of a Base (7). Attach the Base to the indicat- ed end of the Base Crossbar (20) using a Support Plate (57), two M10 x 80mm Bolts (41), and two M10 Nylon Locknuts (11). Do not tight- en the Nylon Locknuts yet.

Attach the other Base (not shown) to the opposite end of the Base Crossbar (20) in the same man- ner.

2.Press a 60mm Square Inner Cap (55) into the end of the Rear Base (3). Attach the Rear Base and the Foot Plate (4) to the Base Crossbar (20) using two M10 x 80mm Bolts (41) and two M10 Nylon Locknuts (11). Do not tighten the Nylon

Locknuts yet.

1

 

 

 

 

41

57

55

 

 

 

 

 

 

7

 

11

 

 

 

55

 

 

 

 

 

 

11

 

 

 

20

2

 

 

 

 

 

11

55

 

 

 

 

 

 

3

 

 

 

11

 

 

 

20

41

 

4

 

5

Image 5
Contents Model No. WEBE29320 Serial No QUESTIONS?Customer HOT Line Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Right Side Before YOU BeginLocknuts yet AssemblyMake Things Easier for Yourself Locknuts yet Tighten the M8 x 20mm Screws 50 used in steps 6 Make sure the Safety Spotters are oriented exactly as shownAngled End Weight Tube Bracket Nylon Locknut the Pulley must be able to Turn freely Tighten all M10 Nylon Locknuts 11 used StepsPage Nylon Locknuts yet Tighten the M10 Nylon Locknuts 11 used in steps Nylon Locknut the Backrest must be able to pivot freely 4661 Using the Safety Spotters AdjustmentsUsing the Locking BAR Using the LEG Lever Attaching Weights to the Barbell or the Weight CarriageTightening the Cables Locknut the Pulley must turn freelyAttaching the Curl PAD Adjusting the BackrestExercise Guidelines Staying Motivated Muscle ChartCooling Down Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty M6 x 36mm Bolt Part Identification ChartQty Description Part LIST-Model No. WEBE29320Exploded DRAWING-Model WEBE29320