Weider PRO 375 user manual

Page 10

17. Slide the indicated end of the High Cable (13)

17

 

 

 

onto the M10 x 20mm Bolt (26) in the Weight

 

 

 

 

13

 

 

Carriage (22). Tighten an M10 Nylon Locknut (11)

 

 

 

 

 

 

 

onto the Bolt.

11

 

 

 

 

 

26

 

 

 

 

22

 

18. Route the High Cable (13) around a Pulley (5) as

18

 

 

 

shown. Hold a Cable Trap (21) against the Pulley

 

 

 

 

 

 

 

and attach a Pulley Plate (19) to each side of the

 

 

 

 

Pulley using an M10 x 45mm Bolt (40) and an

 

 

 

 

M10 Nylon Locknut (11). Make sure the Cable

 

 

 

 

Trap holds the High Cable in the groove of the

 

 

 

 

Pulley. Do not overtighten the Nylon Locknut;

 

13

5

 

the Pulley must be able to turn freely.

 

 

21

 

 

 

11

 

 

 

 

 

 

 

19

40

 

 

 

19. Wrap the indicated end of the Low Cable (8)

19

 

 

 

around a Pulley (5). Attach the Pulley to the

 

 

 

 

 

 

 

bracket on the Base Crossbar (20) using an M10

 

 

 

 

x 45mm Bolt (40) and an M10 Nylon Locknut (11).

 

 

 

 

Do not overtighten the Nylon Locknut; the

8

5

 

Pulley must be able to turn freely.

 

 

 

 

 

 

 

 

 

11

 

 

 

20

 

40

 

20. Route the Low Cable (8) around a Pulley (5) as

20

 

 

 

shown. Hold a Cable Trap (21) against the Pulley

 

 

 

 

 

 

 

and attach the Pulley and Cable Trap to the low-

 

 

 

 

est holes in the two Pulley Plates (19) using an

 

 

 

 

M10 x 45mm Bolt (40) and an M10 Nylon Locknut

 

 

 

 

(11). Make sure the Cable Trap holds the Low

 

 

19

 

Cable in the groove of the Pulley. Do not over-

 

 

 

 

 

 

 

tighten the Nylon Locknut; the Pulley must be

 

11

40

 

able to turn freely.

 

 

 

 

 

5

21

 

 

 

 

 

 

 

8

 

 

 

10

 

 

 

Image 10
Contents Customer HOT Line QUESTIONS?Model No. WEBE29320 Serial No Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Before YOU Begin Right SideMake Things Easier for Yourself AssemblyLocknuts yet Locknuts yet Make sure the Safety Spotters are oriented exactly as shown Tighten the M8 x 20mm Screws 50 used in steps 6Angled End Weight Tube Bracket Tighten all M10 Nylon Locknuts 11 used Steps Nylon Locknut the Pulley must be able to Turn freelyPage Nylon Locknuts yet Tighten the M10 Nylon Locknuts 11 used in steps Nylon Locknut the Backrest must be able to pivot freely 4661 Using the Locking BAR AdjustmentsUsing the Safety Spotters Tightening the Cables Attaching Weights to the Barbell or the Weight CarriageUsing the LEG Lever Locknut the Pulley must turn freelyAdjusting the Backrest Attaching the Curl PADExercise Guidelines Cooling Down Muscle ChartStaying Motivated Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part Identification Chart M6 x 36mm BoltPart LIST-Model No. WEBE29320 Qty DescriptionExploded DRAWING-Model WEBE29320