Weider WEEVSY87210 user manual Be sure that the Cable is routed Around the Pulley as shown

Page 13

CABLE ASSEMBLY

20. Route the Short Cable (58) around the 3 1/2”

20

 

 

 

Pulley (15) attached to the upper hole in the

 

 

 

 

 

 

 

Press Frame (17). Be sure that the Cable

 

 

 

 

Trap (66) is in the “3 o’clock” position and

 

 

 

 

that the Cable is routed around the Pulley

 

 

 

 

as shown. Tighten the 3/8” Nylon Locknut

 

 

 

 

(21) and the 3/8” x 3 3/4” Bolt (not shown).

 

 

 

 

If the indicated 3 1/2” Pulley (15) is pre-

 

 

42

 

 

 

 

 

attached to the Front Upright (42), remove it.

 

 

58

 

Route the Short Cable (58) around the 3 1/2”

 

 

89

 

Pulley. Attach the Pulley and two Pulley

 

 

 

Covers (89) to the upper hole in the Front

 

 

 

71

Upright with the 3/8” Nylon Jam Nut (92), the

 

 

 

 

3/8” Washer (9) and the 3/8” x 3 3/4” Bolt

 

 

 

 

(71). Be sure that the Cable is routed

 

 

 

 

around the Pulley as shown.

 

 

15

 

 

 

 

21

 

 

 

 

66

 

 

 

 

12

 

 

 

 

9

3

 

 

92

6

 

 

 

9

 

 

 

 

 

 

 

 

17

 

21. Attach the end of the Short Cable (58) to the

21

 

 

 

Long “U”-Bracket (57) with a 1/4” Nylon Lock-

 

 

 

 

 

 

 

nut (2) and a 1/4” Washer (10). Do not com-

 

 

 

 

pletely tighten the Nylon Locknut. It

 

 

 

 

should be threaded onto the end of the

 

 

 

 

Cable so only a couple of threads are

 

 

 

 

showing above the Nylon Locknut, as

 

 

 

 

shown in the inset drawing.

 

 

 

 

 

 

2

 

 

 

 

 

57

 

 

 

10

 

 

 

 

 

58

 

 

67

2

 

 

 

 

 

 

 

 

10

 

 

 

58

 

 

 

13

Image 13
Contents Model No. WEEVSY87210 Serial No QUESTIONS?Important Precautions Table of ContentsPage Before YOU Begin Using the weight system. If you have additionalFor your benefit, read this manual carefully before Frame Assembly AssemblyFollowing Tools not Included are Required for Assembly Do not tighten the Nylon Locknuts yetNylon Locknut yet Nylon Locknuts yetLocknut yet Tighten all Nylon Locknuts used in steps 1 throughFrame Assembly Sure that the holes in the Weight Guides Frame Assembly ARM AssemblyAre at the top, as shown Axle-Lubricate Cable Assembly Be sure that the 5/16 x 5 Bolt 68 is tight Ened Cable Assembly Be sure that the Cable is routed Around the Pulley as shown Seat AssemblyPin Seat AssemblyPage Changing the Weight Setting HOW to USE the Weight SystemAttaching the LEG Lever to the LOW Pulley Station Attaching and Removing the SeatChanging the Stepping Resistance Locking the Weight Stack Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceReplace all cables every two years Long Cable 23 TOP View Cable DiagramShort Cable Page Ordering Replacement Parts Remove this Part Identification Chart from the Manual Page X 2 1/2 Screw Save this Part LIST/EXPLODED Drawing for Future Reference Remove this Part LIST/EXPLODED Drawing from the ManualQty Description Part LIST-Model No. WEEVSY87210Drawing