Weider WEEVSY87210 user manual Axle-Lubricate

Page 9

ARM ASSEMBLY

12. Wet the handle of one Press Arm (46) with

12

 

 

soapy water. Slide a 5” Plastic Grip (31) onto

 

 

 

 

 

the handle. Press a 1” Round Inner Cap (49)

 

 

 

into the other end of the handle. Press a 1

 

 

 

3/4” Square Inner Cap (44) into the top of the

 

 

 

Press Arm.

 

 

 

Attach the Press Arm (46) to one side of the

 

 

44

Press Frame (17) with two 5/16” x 2 1/2”

 

 

 

 

 

Bolts (22) and two 5/16” Nylon Locknuts (3).

 

 

 

Assemble the other Press Arm (46) in the

 

 

31

 

 

 

same manner.

 

 

49

 

 

 

 

 

 

46

 

 

22

 

 

 

 

3

 

 

 

17

 

 

46

 

13. Lubricate both axles on the Top Frame (55).

13

 

 

 

55

Bracket

 

 

Slide the Right Arm (48) onto the right axle.

 

 

47

Note: Be careful not to confuse the Right

 

 

 

Arm with the Left Arm (47); note the posi-

 

 

 

tion of the “V” Pulley (6) to identify the

 

 

Axle–Lubricate

Right Arm. Be sure that the upper end of

 

 

the Right Arm is behind the indicated

 

 

45

bracket on the Top Frame (55).

 

6

Tap two 1” Retainers (69) and a 1” Round

 

 

69

Cover Cap (70) onto the axle. Be sure that

 

 

 

 

 

the teeth on the Retainers bend toward the

 

 

70

Cover Cap, as shown in the inset drawing.

 

48

 

 

 

 

44

 

 

 

Attach the Left Arm (47) in the same manner.

 

 

 

Press 1 3/4” Square Inner Caps (44) into the

 

 

 

lower ends of the Left and Right Arms (47,

 

 

 

48). Wet the lower end of each Arm with

 

 

 

soapy water. Slide a 10” Pad (45) onto the

 

 

44

lower end of each Arm.

 

 

 

 

 

45

 

 

 

55—Axle

 

 

 

69

 

 

 

70

9

 

 

 

Image 9
Contents Model No. WEEVSY87210 Serial No QUESTIONS?Important Precautions Table of ContentsPage Using the weight system. If you have additional Before YOU BeginFor your benefit, read this manual carefully before Frame Assembly AssemblyFollowing Tools not Included are Required for Assembly Do not tighten the Nylon Locknuts yetNylon Locknut yet Nylon Locknuts yetLocknut yet Tighten all Nylon Locknuts used in steps 1 throughFrame Assembly Frame Assembly ARM Assembly Sure that the holes in the Weight GuidesAre at the top, as shown Axle-Lubricate Cable Assembly Be sure that the 5/16 x 5 Bolt 68 is tight Ened Cable Assembly Be sure that the Cable is routed Around the Pulley as shown Seat AssemblyPin Seat AssemblyPage Changing the Weight Setting HOW to USE the Weight SystemAttaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley StationChanging the Stepping Resistance Locking the Weight Stack Weight Resistance Chart Troubleshooting and Maintenance Tightening the CablesReplace all cables every two years Cable Diagram Long Cable 23 TOP ViewShort Cable Page Ordering Replacement Parts Remove this Part Identification Chart from the Manual Page X 2 1/2 Screw Save this Part LIST/EXPLODED Drawing for Future Reference Remove this Part LIST/EXPLODED Drawing from the ManualQty Description Part LIST-Model No. WEEVSY87210Drawing