Weider WESY96352 user manual ARM Assembly, Do not tighten the Nylon Locknut yet

Page 10

ARM ASSEMBLY

12.Press a 1” Round Inner Cap (49) into one of the Press Arms (46). Press a 1 3/4” Square Inner Cap (44) into the Press Arm.

Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3).

Assemble the other Press Arm (46) in the same manner.

13.Identify the Right Arm (48) and the Left Arm (47). Note the position of the welded bracket on each Arm. Arm identification is very important for step 14.

Attach a “V”-Pulley (50) and a Long Cable Trap (31) to the Right Arm (48) with a 3/8” x

2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21).

Do not tighten the Nylon Locknut yet.

Attach a “V”-Pulley (50) and a Long Cable Trap (31) to the Left Arm (47) in the same manner.

14.Lubricate both axles on the Top Frame (55).

Slide the Right Arm (48) onto the right axle.

Note: Be careful not to confuse the Right Arm with the Left Arm (47); refer to step 13 to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the Top Frame (55).

Tap two 1” Retainers (69) and a 1” Round Cover Cap (70) onto the axle. Be sure that the teeth on the Retainers bend toward the Round Cover Cap, as shown in the inset drawing.

Attach the Left Arm (47) in the same manner.

Press 1 3/4” Square Inner Caps (44) into the lower ends of the Right and Left Arms (47, 48). Wet the lower end of each Arm with soapy water. Slide a 10” Pad (45) onto the lower end of each Arm.

10

12

 

44

49

 

 

 

 

 

 

46

 

22

 

 

46

 

 

 

 

3

 

 

 

17

 

13

86

31

 

 

31

50

 

 

 

 

Welded

50

 

47

 

 

Brackets

 

 

 

 

 

21

 

48

 

 

 

14

 

 

 

 

55

Bracket

 

 

 

 

47

 

 

Lubricate

 

 

Axle

 

 

48

 

 

 

 

69

 

 

 

 

45

 

 

70

 

 

 

 

44

 

44

Axle

 

 

45

 

69

 

 

 

70

Image 10
Contents Model No. WESY96352 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Dimensions Before YOU BeginFollowing Tools not Included are Required for Assembly AssemblyFrame Assembly Frame AssemblyNylon Locknuts yet Tighten all Nylon Locknuts used in steps Tube is sitting in the pin grooves in the top Weight Bushings should fit on each end of the indi Locate and open the parts bag labeled ARM AssemblyARM Cated tube in the Base. Make sure thatARM Assembly Do not tighten the Nylon Locknut yetARM Assembly Cable Assembly Long Cable Trap is positioned to hold Cable in place Nylon Locknut the Pulley Bracket Must be able to move freelyCable Assembly Locate the Low Cable 23. Route the Low Locate the Military Press Cable 72. Attach Cable Assembly Pulley move smoothly Cable Assembly Seat Assembly Locate and open the parts bag labeled Seat AssemblySeat Assembly Seat Assembly VKR Assembly Locate and open the parts bag labeled VKR AssemblyWeider HOW to USE the Home GYM System Changing the Weight SettingAttaching and Removing the Seat Adjusting the LEG Press PlateAttaching the LEG Lever to the LOW Pulley Station Weight Resistance Chart PlatesTroubleshooting and Maintenance Tightening the CablesCable Diagrams TOP ViewMilitary Press Cable 72 and Leg Press Cable Pivot Arm Leg Press CablePage Page Page Part LIST-Model No. WESY96352 WESY96352 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT