Weider WESY96352 Frame Assembly, Following Tools not Included are Required for Assembly

Page 5

ASSEMBLY

Before beginning assembly, carefully read the following information and instructions:

•Place all parts of the PRO 9635 in a cleared area and remove the packing materials; do not dis- pose of the packing materials until assembly is completed.

•The assembly is broken into five stages: 1) frame assembly, 2) press and butterfly arm assembly,

3) cable and pulley assembly, 4) seat and back- rest assembly, and 5) VKR assembly. The hard- ware for each stage is packaged separately.

•Wait until you begin each assembly stage to open the parts bag labeled for that assembly stage.

•For help identifying the small parts used in assembly, use the PART IDENTIFICATION

CHART located in the center of this manual. Note: Some small parts may have been pre- attached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached.

•As you assemble the PRO 9635 be sure that all parts are oriented as shown in the drawings.

•Tighten all parts as you assemble them, unless instructed to do otherwise.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY:

•Two (2) adjustable wrenches

•One (1) standard screwdriver

•One (1) phillips screwdriver

• One (1) rubber mallet

•Lubricant, such as grease or petroleum jelly, and soapy water will also be needed.

Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

FRAME ASSEMBLY

1.Before beginning assembly, be sure that you have read and understand the infor- mation in the box above.

Locate and open the parts bag labeled

“FRAME ASSEMBLY.”

Press two 2” Square Outer Caps (51) onto the indicated locations on the Stabilizer (5). Press a 2” Square Inner Cap (27) into the end of the Base (4).

Insert six 5/16” x 2 1/2” Carriage Bolts (1) up through the Stabilizer (5). Insert two 5/16” x 2 1/2” Carriage Bolts up through the Base

(4).

Attach the Base (4) to the Stabilizer (5) with two 5/16” x 2 3/4” Bolts (11), two 5/16” Flat Washers (8), and two 5/16” Nylon Locknuts

(3). Do not tighten the Nylon Locknuts yet.

1

 

 

 

 

 

11

 

 

 

51

 

 

 

 

 

 

8

 

5

 

 

 

 

 

 

 

 

1

51

1

3

 

 

 

 

 

4

1

 

 

 

 

 

 

 

 

27

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Customer HOT Line QUESTIONS?Model No. WESY96352 Serial No Table of Contents Important Precautions Before YOU Begin DimensionsFrame Assembly AssemblyFollowing Tools not Included are Required for Assembly Frame AssemblyNylon Locknuts yet Tighten all Nylon Locknuts used in steps Tube is sitting in the pin grooves in the top Weight ARM Locate and open the parts bag labeled ARM AssemblyBushings should fit on each end of the indi Cated tube in the Base. Make sure thatDo not tighten the Nylon Locknut yet ARM AssemblyARM Assembly Cable Assembly Nylon Locknut the Pulley Bracket Must be able to move freely Long Cable Trap is positioned to hold Cable in placeCable Assembly Locate the Low Cable 23. Route the Low Locate the Military Press Cable 72. Attach Cable Assembly Pulley move smoothly Locate and open the parts bag labeled Seat Assembly Cable Assembly Seat AssemblySeat Assembly Locate and open the parts bag labeled VKR Assembly Seat Assembly VKR AssemblyWeider Changing the Weight Setting HOW to USE the Home GYM SystemAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateAttaching and Removing the Seat Plates Weight Resistance ChartTightening the Cables Troubleshooting and MaintenanceTOP View Cable DiagramsLeg Press Cable Military Press Cable 72 and Leg Press Cable Pivot ArmPage Page Page Part LIST-Model No. WESY96352 WESY96352 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents