Weider WESY96352 user manual Attaching and Removing the Seat, Adjusting the LEG Press Plate

Page 23

ATTACHING AND REMOVING THE SEAT

40

 

 

 

 

13

 

 

To attach the Seat (13), set the bracket on the Seat

36

 

 

 

 

 

 

Frame (36) onto the indicated pins on the Front

 

 

 

 

Upright (42). Attach the Seat Frame to the Front

 

 

 

 

Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and

 

 

 

 

the Seat Knob (40).

42

 

 

 

For some exercises, the Seat (13) must be removed.

14

 

 

 

First, be sure that the chain is not attached to the leg

 

 

 

lever. Next, remove the Seat Knob (40) and the 5/16”

 

 

 

 

x 2 3/4” Carriage Bolt (14) from the Seat Frame (36).

 

 

 

 

Lift the Seat Frame off the Front Upright (42).

 

 

 

 

ATTACHING THE LEG LEVER TO THE LOW

 

 

 

 

PULLEY STATION

 

 

 

 

To use the Leg Lever (29), the seat must be attached

 

 

 

 

to the front upright (see ATTACHING AND REMOV-

 

 

 

 

ING THE SEAT above).

 

53

 

 

 

 

52

29

Attach one end of the Chain (52) to the Short Cable

 

 

 

 

35

 

 

 

(23) with a Cable Clip (53). Attach the other end of

 

 

 

 

the Chain to the 3/8” x 2” Eyebolt (35) with a Cable

 

53

 

 

Clip.

 

 

 

 

 

 

 

 

23

 

 

 

ADJUSTING THE LEG PRESS PLATE

 

 

 

 

Remove the Press Pin (97) from the Leg Press Plate

Welded

 

 

95

(95) and the Leg Press Arm (96).

 

 

 

Tube

 

 

 

Align the welded tubes on the Leg Press Plate (95)

 

 

 

 

with the desired set of holes in the Leg Press Arm

 

 

 

 

(96). Re-insert the Press Pin (97) through the welded

 

 

 

97

tubes on Leg Press Plate and the holes in the Leg

 

 

 

Press Arm.

 

 

 

 

 

96

 

 

 

23

Image 23
Contents Customer HOT Line QUESTIONS?Model No. WESY96352 Serial No Table of Contents Important Precautions Before YOU Begin DimensionsFrame Assembly AssemblyFrame Assembly Following Tools not Included are Required for AssemblyNylon Locknuts yet Tighten all Nylon Locknuts used in steps Tube is sitting in the pin grooves in the top Weight Cated tube in the Base. Make sure that Locate and open the parts bag labeled ARM AssemblyARM Bushings should fit on each end of the indiDo not tighten the Nylon Locknut yet ARM AssemblyARM Assembly Cable Assembly Nylon Locknut the Pulley Bracket Must be able to move freely Long Cable Trap is positioned to hold Cable in placeCable Assembly Locate the Low Cable 23. Route the Low Locate the Military Press Cable 72. Attach Cable Assembly Pulley move smoothly Locate and open the parts bag labeled Seat Assembly Cable Assembly Seat AssemblySeat Assembly Locate and open the parts bag labeled VKR Assembly Seat Assembly VKR AssemblyWeider Changing the Weight Setting HOW to USE the Home GYM SystemAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateAttaching and Removing the Seat Plates Weight Resistance ChartTightening the Cables Troubleshooting and MaintenanceTOP View Cable DiagramsLeg Press Cable Military Press Cable 72 and Leg Press Cable Pivot ArmPage Page Page Part LIST-Model No. WESY96352 WESY96352 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty