Weider WESY96352 user manual HOW to USE the Home GYM System, Changing the Weight Setting

Page 22

HOW TO USE THE HOME GYM SYSTEM

The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise.

IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the cor- rect starting position for the exercise to be performed. If there is any slack in the cables or chain as an exercise is performed, the effectiveness of the exercise will be reduced.

CHANGING THE WEIGHT SETTING

The PRO 9635 features two weight stacks. The front weight stack is connected to the upper and lower pul- leys, the press arm, and the butterfly arms. The rear weight stack is connected to the military press arm and leg press.

To change the weight setting of either weight stack, insert a Weight Pin (26) under the desired Weight (25). Insert the Weight Pin until the bent end of the Weight Pin is touching the Weights, and turn the bent end downward. The weight setting of either weight stack can be changed from 6.5 pounds to 106.5 pounds, in increments of 12.5 pounds. Note: Due to the cables and pulleys, the amount of resistance at each exercise station may vary from the weight setting. Use the WEIGHT RESISTANCE CHART on page 24 to find the approximate amount of resis- tance at each weight station.

ATTACHING THE LAT BAR OR NYLON STRAP TO THE HIGH PULLEY STATION

Attach the Lat Bar (54) to the High Cable (58) with a Cable Clip (53). For some exercises, the Chain (52) should be attached between the Lat Bar and the High Cable with two Cable Clips. Adjust the length of the

Chain between the Lat Bar and the High Cable so the Lat Bar is in the correct starting position for the exercise to be performed.

The Nylon Strap (39) can be attached in the same manner.

ATTACHING THE LAT BAR OR NYLON STRAP TO THE LOW PULLEY STATION

Attach the Lat Bar (54) to the Low Cable (23) with a Cable Clip (53). For some exercises, the Chain (52) should be attached between the Lat Bar and the Low Cable with two Cable Clips. Adjust the length of the

Chain between the Lat Bar and the Low Cable so the Lat Bar is in the correct starting position for the exercise to be performed.

The Nylon Strap (39) can be attached in the same manner.

26

 

25

 

25

 

 

26

53

52

 

58

53

 

54

 

39

23

 

53

52

 

53

 

39

 

54

22

 

Image 22
Contents Model No. WESY96352 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Dimensions Before YOU BeginFollowing Tools not Included are Required for Assembly AssemblyFrame Assembly Frame AssemblyNylon Locknuts yet Tighten all Nylon Locknuts used in steps Tube is sitting in the pin grooves in the top Weight Bushings should fit on each end of the indi Locate and open the parts bag labeled ARM AssemblyARM Cated tube in the Base. Make sure thatARM Assembly Do not tighten the Nylon Locknut yetARM Assembly Cable Assembly Long Cable Trap is positioned to hold Cable in place Nylon Locknut the Pulley Bracket Must be able to move freelyCable Assembly Locate the Low Cable 23. Route the Low Locate the Military Press Cable 72. Attach Cable Assembly Pulley move smoothly Cable Assembly Seat Assembly Locate and open the parts bag labeled Seat AssemblySeat Assembly Seat Assembly VKR Assembly Locate and open the parts bag labeled VKR AssemblyWeider HOW to USE the Home GYM System Changing the Weight SettingAttaching and Removing the Seat Adjusting the LEG Press PlateAttaching the LEG Lever to the LOW Pulley Station Weight Resistance Chart PlatesTroubleshooting and Maintenance Tightening the CablesCable Diagrams TOP ViewMilitary Press Cable 72 and Leg Press Cable Pivot Arm Leg Press CablePage Page Page Part LIST-Model No. WESY96352 WESY96352 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT