Weider WESY39523 user manual 100 102

Page 13

24.Remove the preattached 90mm Pulleys (78) from the Offset Double “U”-bracket (61).

Wrap the Swivel Cable (17) around a 90mm Pulley (78). Attach the Pulley to the Offset Double “U”- bracket (61) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87).

25.Wrap the Swivel Cable (17) around a 90mm Pulley (78). Attach the Pulley and a Cable Trap (68) to the next to bottom hole in the Small Pulley Plates (31) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the Cable Trap is turned to hold the Cable in the groove of the Pulley.

26.Wrap the Swivel Cable (17) around a 90mm Pulley (78). Attach the Pulley and a Long Cable Trap (102) to the bracket on the Swivel Upright (5) with an

M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the Cable Trap is turned to hold the Cable in the groove of the Pulley.

27.Attach the end of the Swivel Cable (17) to the bracket on the Swivel Carriage (46) with an M10 x 20mm Bolt (86) and an M10 Nylon Locknut (87).

28.Locate the Lat Cable (88), which is 2263mm long and has a ball on one end and an eyelet on the other. Route the eyelet end of the Cable up through the Butterfly Top Frame (7) and around a 90mm Pulley (78). Attach the Pulley inside of the Butterfly Top Frame with an M10 x 65mm Bolt (101), two M10 Washers (91), two 12mm Spacers (89), and an M10 Nylon Locknut (87).

13

24

 

 

 

 

 

 

 

17

 

 

 

 

78

 

 

 

93

 

 

 

61

87

 

 

 

 

 

25

 

 

 

 

 

 

31

 

100

 

 

87

 

 

 

 

 

 

 

78

 

 

 

 

17

68

 

 

 

 

 

26

 

 

100

 

 

5

 

 

 

 

 

 

 

102

 

 

 

87

 

 

 

 

 

 

17

 

 

 

 

78

 

27

 

 

 

 

 

46

 

 

 

 

87

 

86

 

 

 

 

 

 

 

 

17

 

28

 

 

 

 

 

87

78

 

 

 

 

 

 

 

91

 

 

 

 

89

 

89

 

 

 

 

 

 

7

 

91

18

 

 

 

 

88

 

 

 

Image 13
Contents Model No. WESY39523 Serial No QUESTIONS?Customer HOT Line Table of Contents Decal Important PrecautionsBefore YOU Begin Using the weight system. If you have additionalFor your benefit, read this manual carefully before DecalAssembly Frame Assembly Do not tighten the Locknuts yet Page Assemble the other weight stack in the same way Tighten all of the M10 Nylon Locknuts 87 used in steps Open the parts bag labeled ARM AssemblyButterfly Frame must be able to pivot easily Cable Assembly 119 100 118 100 102 Trap is turned to hold the Cable in the groove of the Pulley Page Page Trap is turned to hold the Cable in the groove of the Pulley Trap is turned to hold the Cable in the groove of the Pulley Locate and open the parts bag labeled Seat Assembly Seat AssemblyLocknuts yet Repeat this step with the other end of the Squat ArmTighten all of the M10 Nylon Locknuts 87 used in this step Page Changing the Weight Setting AdjustmentsConverting the Butterfly Arms Ing any exerciseAdjusting the Squat Knee Rest Adjusting the Squat ARM, SEAT, or Butterfly BackrestStation Weight Resistance ChartLbs Top Tightening the Cables TroubleshootingLat Cable Cable DiagramsButterfly Cable Swivel High Cable Squat Cable Swivel Cable Leg LeverSwivel Low Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Page R0103A Part Identification CHART-Model No. WESY39523Page Page Remove this Part LIST/EXPLODED Drawing From the Manual Key Qty Description Part LIST-Model No. WESY39523Exploded