Weider WESY39523 user manual

Page 16

39.Route the Leg Lever Cable (75) under a 115mm Pulley (119). Attach the Pulley and a Large Cable Trap (113) to the indicated side of the Butterfly Upright (3) with an M10 x 95mm Bolt (92), an M10 Washer (91), and an M10 Nylon Locknut (87).

Make sure that the Large Cable Trap is turned to hold the Cable in the groove of the Pulley.

40.Wrap the Leg Lever Cable (75) over a 90mm Pulley

(78).Attach the Pulley to the Double “U”-bracket

(62)with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87).

41.Remove the preattached 90mm Pulley (not shown) from the “U”-bracket (64).

Attach the end of the Leg Lever Cable (75) to the “U”-bracket (64) with an M8 Washer (90) and an M8 Nylon Locknut (34). Note: Do not completely tighten the Locknut; it should be threaded only two turns onto the end of the Cable, as shown in the inset drawing.

42.Locate the Swivel Low Cable (72), which is the only remaining cable that has an eyelet on one end and a ball on the other end. Route the eyelet end of the Cable through the cage on the Long Base (101) and through the Swivel Upright (5), as shown. Make sure the Cable is over the short bar inside the cage.

Attach a 90mm Pulley (78) to the indicated bracket on the Long Base (101) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87). Make sure the Cable is in the groove of the Pulley.

43.Wrap the Swivel Low Cable (72) under a 90mm Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (101) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87).

16

39

 

 

 

119

 

92

 

 

113

 

 

 

3

 

 

75

 

 

91

87

40

 

 

 

93

 

 

62

 

 

87

 

 

75

 

 

78

 

41

 

 

64

75

75

90

 

 

 

34

 

 

 

34

42

 

 

78

 

 

72

 

 

Cage

87

 

 

 

101

5

 

93

 

43

 

 

 

72

 

78

 

 

101

87

 

93

 

 

 

Image 16
Contents Model No. WESY39523 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions DecalUsing the weight system. If you have additional Before YOU BeginFor your benefit, read this manual carefully before DecalAssembly Frame Assembly Do not tighten the Locknuts yet Page Assemble the other weight stack in the same way Tighten all of the M10 Nylon Locknuts 87 used in steps Open the parts bag labeled ARM AssemblyButterfly Frame must be able to pivot easily Cable Assembly 119 100 118 100 102 Trap is turned to hold the Cable in the groove of the Pulley Page Page Trap is turned to hold the Cable in the groove of the Pulley Trap is turned to hold the Cable in the groove of the Pulley Seat Assembly Locate and open the parts bag labeled Seat AssemblyLocknuts yet Repeat this step with the other end of the Squat ArmTighten all of the M10 Nylon Locknuts 87 used in this step Page Adjustments Changing the Weight SettingConverting the Butterfly Arms Ing any exerciseAdjusting the Squat ARM, SEAT, or Butterfly Backrest Adjusting the Squat Knee RestStation Weight Resistance ChartLbs Top Troubleshooting Tightening the CablesLat Cable Cable DiagramsButterfly Cable Swivel High Cable Squat Cable Swivel Cable Leg LeverSwivel Low Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Page Part Identification CHART-Model No. WESY39523 R0103APage Page Remove this Part LIST/EXPLODED Drawing From the Manual Part LIST-Model No. WESY39523 Key Qty DescriptionExploded