Whirlpool ELECTRONIC GAS DRYER manual Install VentSystem, Install LevelingLegs, LevelDryer

Page 12

Determine vent path

Select the route that will provide the straightest and most direct path outdoors.

Plan the installation to use the fewest number of elbows and turns.

When using elbows or making turns, allow as much room as possible.

Bend vent gradually to avoid kinking.

Use the fewest 90° turns possible.

Determine vent length and elbows needed for best drying performance

Use the following Vent system chart to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those specified will:

Shorten the life of the dryer.

Reduce performance, resulting in longer drying times and increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90º turn inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart.

Number of

Type of

Box or

Angled

90º turns

vent

louvered

hoods

or elbows

 

hoods

 

 

 

 

 

0

Rigid metal

64 ft (20 m)

58 ft (17.7 m)

 

Flexible metal

36 ft (11 m)

28 ft (8.5 m)

 

 

 

 

1

Rigid metal

54 ft (16.5 m)

48 ft (14.6 m)

 

Flexible metal

31 ft (9.4 m)

23 ft (7 m)

 

 

 

 

2

Rigid metal

44 ft (13.4 m)

38 ft (11.6 m)

 

Flexible metal

27 ft (8.2 m)

19 ft (5.8 m)

 

 

 

 

3

Rigid metal

35 ft (10.7 m)

29 ft (8.8 m)

 

Flexible metal

25 ft (7.6 m)

17 ft (5.2 m)

 

 

 

 

4

Rigid metal

27 ft (8.2 m)

21 ft (6.4 m)

 

Flexible metal

23 ft (7 m)

15 ft (4.6 m)

Install VentSystem

1.Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

2.Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3.Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in “Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent.

Install LevelingLegs

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1.To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.

2.Firmly grasp the body of the dryer. Gently lay the dryer on the cardboard. See illustration.

3.Examine the leveling legs. Find the diamond marking.

4.Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible.

5.Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor at the time of installation.

Mobile home installations require a Mobile Home Installation Kit. For more information, please reference the service numbers in the “Assistance or Service” section of this manual.

LevelDryer

Check the levelness of the dryer. Check levelness first side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

12

Image 12
Contents Electronic GAS Dryer W10110851ATable of Contents Dryer Safety Your safety and the safety of others are very importantImportant Safety Instructions Installation Instructions ToolsandPartsOptions LocationRequirements Installation Mobile home Additional installation requirements Electrical RequirementsGas SupplyRequirements Gas TypeGas supply pressure testing If using an existing vent systemVentingRequirements Dryer gas pipeIf this is a new vent system Vent material Optional exhaust installations Special provisions for mobile home installationsAlternate installations for close clearances Plan VentSystemInstall VentSystem Install LevelingLegsLevelDryer CompleteInstallation MakeGasConnectionConnectVent If the dryer will not start, check the followingDryer USE StartingYourDryerTo use an Automatic Cycle PausingorRestarting StoppingYourDryerControlLocked DryingandCycleTipsStatusLights CyclesAdditional Features DryingRackOption ChangingCycles,Options andModifiersCleaningtheDryer Location CleaningtheLintScreenEvery load cleaning As needed cleaningCleaningtheDryerInterior RemovingAccumulatedLintVacationandMovingCare ChangingtheDrumLightTroubleshooting DryerOperationCycle time too short Lint on loadStains on load or drum Loads are wrinkledAssistance or Service TheU.S.AInCanada Whirlpool Corporation Major Appliance Warranty CallSécurité DE LA Sécheuse Votre sécurité et celle des autres est très importanteInstructions D’INSTALLATION OutillageetpiècesPièces fournies Pièces nécessairesPiédestal Nécessaire de superpositionTrousse dinversion de porte Trousse dinversion de la porte et ensemble de superpositionExigencesd’emplacement Dimensions de la sécheuseIl vous faudra Dégagements de séparation à respecterEspacement recommandé pour linstallation dans un placard Installation dans un placard Sécheuse seulementLes dimensions indiquées sont pour lespacement recommandé Espacement requisLinstallation dans une maison mobile exige SpécificationsélectriquesAlimentation en gaz Type de gazCaractéristiques d’alimentation du brûleur Canalisation d’arrivée de gaz de la sécheuseExigences concernantlévacuation En cas dutilisation du système dévacuation existantConduit métallique flexible CoudesInstallations d’évacuation facultatives Les styles de clapets recommandés sont illustrés ci-dessousPlanificationdu systèmed’évacuation ÉvacuationAutres installations où le dégagement est réduit Déterminer litinéraire dacheminement du conduitTableau des systèmes dévacuation Une réduction de la longévité de la sécheuseInstallation dusystèmed’évacuation InstallationdespiedsdenivellementMiseàniveau dela sécheuse RaccordementaugazAcheverl’installation Raccordementdu conduitd’évacuationLa sécheuse Si la sécheuse ne démarre pas, vérifier ce qui suitUtilisation DE LA Sécheuse MiseenmarchedelasécheuseUtilisation dun programme automatique Arrêtdelasécheuse Pauseou remiseenmarchePour arrêter la sécheuse à nimporte quel moment Pour mettre la sécheuse en pause à nimporte quel momentConseils pourleséchageetles programmes TémoinslumineuxProgrammes Caractéristiquessupplémentaires Changementdesprogrammes,optionset Modificateurs Option degrilledeséchageButton Sound son des boutons Changement des programmes après avoir appuyé sur StartNettoyagedelemplacementde Lasécheuse Nettoyagedu filtreàcharpieNettoyage à chaque charge Nettoyagedel’intérieurdelasécheuse RetraitdelacharpieaccumuléePrécautionsàprendrepourlesvacancesetavantun Déménagement Changementdel’ampouled’éclairage Du tambourDépannage FonctionnementdelasécheuseRésultatsdelasécheuse Temps de programme trop court Charpie sur la chargeTaches sur la charge ou sur le tambour Charges froisséesAssistance OU Service AuxÉtats-UnisAu Canada Garantie DES Gros Appareils Ménagers Whirlpool Corporation Composer le 1-800-253-1301. Au Canada, composer leW10110851A

ELECTRONIC GAS DRYER specifications

The Whirlpool Electronic Gas Dryer is an innovative household appliance designed to streamline your laundry experience while ensuring optimal performance and efficiency. Packed with advanced features and cutting-edge technologies, this gas dryer caters to the needs of modern consumers who prioritize convenience, energy efficiency, and superior fabric care.

One of the standout features of the Whirlpool Electronic Gas Dryer is its precise drying technology, which includes moisture sensing capability. This intelligent system detects the moisture level in your clothes, automatically adjusting drying time accordingly. This not only helps prevent overdrying, which can damage fabrics and reduce lifespan, but also conserves energy by reducing unnecessary drying cycles.

Another significant aspect of this dryer is its variety of drying cycles. From Delicate and Heavy Duty to Quick Dry settings, the Whirlpool Electronic Gas Dryer offers customizable options for various fabric types and load sizes. This flexibility is enhanced by the inclusion of specialty cycles, such as Sanitize and Steam Refresh, which address specific care needs for items like bedding and athletic wear.

Energy efficiency is a key consideration in the design of the Whirlpool Electronic Gas Dryer. With an Energy Star certification, it meets stringent energy efficiency guidelines, helping homeowners save on utility bills while reducing their ecological footprint. This dryer uses gas as its primary heat source, which is typically more cost-effective and environmentally friendly compared to electric alternatives.

User-friendly controls make operating the Whirlpool Electronic Gas Dryer a breeze. The intuitive digital display allows for easy selection of drying cycles and settings, while the end-of-cycle signal alerts you when your laundry is ready. Additionally, the front-loading design and large capacity drum can accommodate substantial loads, making it ideal for busy households.

The durable construction of the Whirlpool Electronic Gas Dryer ensures long-lasting performance. High-quality materials and robust components contribute to its reliability, while the sleek design adds a modern touch to any laundry room. Overall, the Whirlpool Electronic Gas Dryer combines the latest technologies with thoughtful features, providing an effective solution for tackling laundry day challenges with ease and efficiency.